Edwards D397-50-000 Instruction Manual Download Page 40 | Manualshive

Page: 40 / 76

background image

D397-50-880 Issue C

Page 34

© Edwards Limited 2010. All rights reserved.

Edwards and the Edwards logo are trademarks of Edwards Limited.

Operation

Associated Parameter options (bytes 3-14 relate to linking gauges)

4.8.19

Software module 914 - Gauge 2

This module can be used with any TIC version that includes gauge control.

General Description

Control and monitoring of Gauge connected to gauge port number 2.
See Gauge 1 for output, input and parameter options.

4.8.20

Software module 915 - Gauge 3

This module can be used with any TIC version that includes gauge control.

General Description

Control and monitoring of Gauge connected to gauge port number 3.
See Gauge 1 for output, input and parameter options.

4.8.21

Linking Relay set point outputs

The TIC Profibus module can be used to provide relay set point outputs based on gauge pressure, volts, or pump
speed. Further information about relay set point outputs can be read in the TIC instruction manual D397 22 880
Section 4.16. The information below provides details about linking using the TIC Profibus module.

Linking can be set up by parameterisation of the TIC such that the linked items will turn on/off at the specified
pressures, voltages or speeds from a master item.

Controlling item (Master object)

- The item that will control the relay.

Units

- The unit value must be a suitable type for the controlling item or the set-up will be ignored by the TIC i.e.

must use speed for a Turbo pump and must use pressure or volts for a gauge.

Bytes

Parameter Option

Description of Parameter

1st

Module number

Cannot be changed.

2nd

3rd

Controlling item

Master object.

4th
5th

Units

For Master object not Slave object.

6th

Setpoint ON

IEEE-754 format for pressure and voltage.

7th
8th
9th

10th

Setpoint OFF

IEEE-754 format for pressure and voltage.

11th
12th
13th
14th

Enable

Enables or disables control at the chosen setpoint.

15th

Gas type

This option also determines signal units. All except voltage
options will be in Pascal’s (IEEE-754 format).

16th

Filter

Either no gauge signal filtering or a 1 second averaging filter
can be selected.

17th

ASG range

If the gauge is a strain gauge the full-scale range must be
selected as either 1000 mbar or 2000 mbar.

«
...
38
39
40
41
42
...
»

Summary of Contents for D397-50-000













































































Reviews:

No comments

Related manuals for D397-50-000

Brand: UNITED Pages: 22

SmartSwitch 6000

Brand: Cabletron Systems Pages: 76

Brand: Lattice Semiconductor Pages: 2

Brand: Lathem Pages: 4

Brand: tams elektronik Pages: 36

Brand: IBM Pages: 38

Brand: Rane Pages: 2

Brand: L-Acoustics Pages: 20

Brand: Eaton Pages: 96

Brand: K&G GROEP Pages: 27

Brand: CAME Pages: 2

Brand: CalAmp Pages: 13

Brand: Daikin Pages: 46

Brand: Daikin Pages: 26

Brand: National Instruments Pages: 78

Brand: M-system Pages: 10

Brand: bluelab Pages: 39

Brand: SOMFY Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands