Edwards D397-50-000 Instruction Manual Download Page 34

Page: 34 / 76

D397-50-880 Issue C

Page 28

Edwards and the Edwards logo are trademarks of Edwards Limited.

Operation

4.8.7

Software module 902 - TIC Software Version

General Description

Module used in TIC Profibus unit to read the software version it contains. This would normally only be
used during setup or test; as it can't alter during data exchange it would not normally be present.

Output bytes (from Master)

None.

Input bytes (to Master)

Associated Parameter options

None.

4.8.8

Software module 904 - Turbo Pump control

This module should be used with any Turbo pump that is compatible with a TIC unit.

General Description

Controls Turbo pumps connected to a TIC.

Output bytes (from Master)

Input bytes (to Master)

1st

Release state of software in ASCII, should be 'P' for production.
e.g.

ASCII ’P’ = 50 h.

2nd

Version letter of software in ASCII, normally A to Z. e.g.

ASCII

’A’

= 41 h.

1st

Stop if value 0. Run if value 1. Leave alone if value 99 (dec). See
note in

Section 4.8.17

1st

State - refer to table in Appendix A1.

2nd

Alert - refer to table in Appendix A2.

3rd

Priority - refer to table in Appendix A3.

Summary of Contents for D397-50-000








































































Search results

Summary of Contents for D397-50-000

Reviews:

Related manuals for D397-50-000

Brands by name

Popular brands

Edwards D397-50-000, Instruction Manual

Search results

Summary of Contents for D397-50-000

Reviews:

Related manuals for D397-50-000

Brands by name

Popular brands