Edwards D397-50-000 Instruction Manual Download Page 33

Page: 33 / 76

Page 27

Edwards and the Edwards logo are trademarks of Edwards Limited.

Operation

D397-50-880 Issue C

4.8.4

Software module 860 - DX Pump Power

This module must only be selected if there is a DX pump connected to the TIC.

General Description

Read DX Pump motor power consumption.

Output bytes (from Master)

None.

Input bytes (to Master)

Associated Parameter options

None.

4.8.5

Software module 869 - DX Pump Speed Set-up

Note:

This module must only be selected if there is a DX pump connected to the TIC.

General Description

Defines DX Pump normal and standby speeds.

Output bytes (from Master)

Input bytes (to Master)

None.

Associated Parameter options

4.8.6

Software module 875 - DX Vent Valve close

General Description

Forces vent valve closed (by powering it) regardless of vent valve control set-up.

Output bytes (from Master)

Once a "forced close" command has been sent it can only be cleared in the DX pump podule by demanding the pump
to stop (using software module 904).

Input bytes (to Master)

None.

Associated Parameter options

None.

1st

Forms a 16-bit (unsigned) number, which is the motor power in
10th’s of Watts.

2nd

1st

Not used with a TIC (preferably leave as zero). Use Module 908 to
go to standby.

Bytes

Parameter Option

Description of Parameter

1st

Module number

Cannot be changed.

2nd

3rd

Normal speed indicator

The value as a percentage of the full speed to define normal
speed indication. (50-100%).

4th

Standby speed

The value as a percentage of the full speed to define standby
speed. (55-100%).

1st

Not forced closed if value 0. Forced closed if value 1.

Summary of Contents for D397-50-000








































































Search results

Summary of Contents for D397-50-000

Reviews:

Related manuals for D397-50-000

Brands by name

Popular brands

Edwards D397-50-000, Instruction Manual

Search results

Summary of Contents for D397-50-000

Reviews:

Related manuals for D397-50-000

Brands by name

Popular brands