Edwards D397-50-000 Instruction Manual Download Page 37

Page: 37 / 76

Page 31

Edwards and the Edwards logo are trademarks of Edwards Limited.

Operation

D397-50-880 Issue C

Input bytes (to Master)

No Alerts currently exist for these software modules so the 2nd and 3rd bytes will always be zero.

Associated Parameter options

None.

4.8.13

Software module 909 - Turbo Cycle Time

This module can be used with any Turbo pump that is compatible with a TIC unit.

General Description

Monitors turbo pump running time, since it was last started.

Output bytes (from Master)

None.

Input bytes (to Master)

No Alerts currently exist for these software modules so the 4th and 5th bytes will always be zero.

Associated Parameter options

None.

4.8.14

Software module 910 - Backing pump control

This module can be used with any TIC that includes pump control.

General Description

Controls Backing Pump.

Output bytes (from Master)

Input bytes (to Master)

No Alerts currently exist for these software modules so the 2nd and 3rd bytes will always be zero.

Associated Parameter options

None.

1st

Whether Standby speed mode is set: 0 =No; 4 = Yes.

2nd

Alert - refer to table in Appendix A2.

3rd

Priority - refer to table in Appendix A3.

1st

First two bytes form a 16-bit number which is the turbo
running time in hours since the pump was started.

2nd

3rd

State - refer to table in Appendix A1.

4th

Alert - refer to table in Appendix A2.

5th

Priority - refer to table in Appendix A3.

1st

Backing pump control (1 = run; 0= stop).

1st

State - refer to table in Appendix A1.

2nd

Alert - refer to table in Appendix A2.

3rd

Priority - refer to table in Appendix A3.

Summary of Contents for D397-50-000








































































Search results

Summary of Contents for D397-50-000

Reviews:

Related manuals for D397-50-000

Brands by name

Popular brands

Edwards D397-50-000, Instruction Manual

Search results

Summary of Contents for D397-50-000

Reviews:

Related manuals for D397-50-000

Brands by name

Popular brands