manualshive.com logo in svg

EDNord magicolor 5450, User Manual

Share
Download
EDNord magicolor 5450 User Manual Download Page 108

Replacing Consumables

94

Replacing Consumables

Note

Failure to follow instructions as outlined in this manual could result in 
voiding your warranty.

Note

If an error message (

TONER EMPTY

, 

TRANS.BELT END OF LIFE

, etc.) 

appears, print out the configuration page, and then check the status of the 
other consumables. For details on the error messages, refer to “Error 
Messages (Warning:)” on page 161. For details on printing the 
configuration page, refer to “Printing a Configuration Page” on page 128.

About Toner Cartridges

Your printer uses four toner cartridges: black, yellow, magenta, and cyan. 
Handle the toner cartridges carefully to avoid spilling toner inside the printer 
or on yourself.

!"

Install only new toner cartridges in your printer. If a used toner car-
tridge is installed, the indicator message will not clear and the supplies 
status in the Status Monitor will not be updated.

!"

The toner is nontoxic. If you get toner on your skin, wash it off with 
cool water and a mild soap. If you get toner on your clothes, lightly 
dust them off as best as you can. If some toner remains on your 
clothes, use cool, not hot water, to rinse the toner off.

CAUTION

If you get toner in your eyes, wash it out immediately with cool water 
and consult a doctor. 

!"

Refer to the following URL for recycling information. 
US: printer.konicaminolta.com/products/recycle/index.asp 
Europe: printer.konicaminolta.com

Note

Do not use refilled toner cartridges or unapproved toner cartridges. Any 
damage to the printer or quality problems caused by a refilled toner 
cartridge or an unapproved toner cartridge will void your warranty. No 
technical support is provided to recover from these problems.

EDNord - Istedgade 37A - 9000 Aalborg - telefon 9633350

Summary of Contents for magicolor 5450

















































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands