background image

32

8 - ELECTRICAL CONNECTIONS

• 

Outdoor Sensor, if used.

A.  Provided with boiler in accessory kit.

B.  Locate outdoor sensor to protect against wind and 

direct sunlight. Mounting instructions provided with 

sensor. 

C.  Maximum wire length is 100 ft (30m) for 22 ga. 

wire, or 150 ft (45m) for 18 ga. wire.

D.  Connect wires to low voltage terminal plug 

OUTDOOR SENSOR terminals. Wires are 

interchangeable.

• 

System Sensor (Multiple boiler applications only)

• 

Domestic Hot Water (DHW) Thermostat, if used.

A.  Use temperature control with dry contacts rated 

at 0.5 amps @ 120 VAC. Boiler control does not 

provide power to DHW temperature control. 

NOTICE

Do not apply power to DHW T-T terminals.  Dry 

contact only, use of isolation relay may be necessary.

B.  Maximum wire length is 330 ft (100 m) 22 gauge 

wire.

C.  Connect  wires  (interchangeable)  to  low  voltage                                              

terminal plug DHW T-T terminals. Wires are              

interchangeable.

• 

Central Heating Thermostat

A.  Use thermostat or boiler system control with dry 

contacts related 0.5 amps @ 120 VAC.

 

Boiler 

control does not provide 24 VAC power to central 

heating thermostat.

B.  Locate and install thermostat per manufacturer's 

instructions. Maximum wire length is

 

330 ft (100 

m) for 22 ga. wire.

C.  Connect wires to low voltage terminal plug CH T-T 

terminals. Wires are interchangeable.

NOTICE

Use dry contact for wires to CH T-T terminal and  

DHW T-T terminal. E33 error code is displayed if 

voltage is sent back to the control board. If error 

is not corrected for extended period of time, this 

voltage can permanently damage control board.

Summary of Contents for 075 97gb

















































































Reviews: