EcoWater CHC Series Service And Troubleshooting Manual Download Page 68 | Manualshive

Page: 68 / 130

EcoWater CHC Series Service And Troubleshooting Manual Download Page 68

68

5.8

Leaks-

The majority of the leaks will require the replacement of the defective parts. However, always verify
that the hardware does not need to be tightened first to correct the issue.

5.8.1

O-Ring Leaks or Failure-

Replace defective O-Ring, and lubricate with appropriate silicone lubricant.

5.8.2

Flange gasket Leaks-

Tighten the flanges or replace the gasket.

5.8.3

Plumbing Leaks or Failure-

Contact the appropriate personnel to make corrections to plumbing.

5.8.4

Valve Leaks or Failure-

Contact the appropriate personnel to make corrections to plumbing.

5.8.5

Internal Valve Leaks-

In some cases you may find that the blow down actuator has a continuous leak, even in the
closed position. If you find this you will need to replace the blow down valve.

5.8.6

Vacuum Leaks-

Vacuum leaks on the CHC system can be a cause for concern, because they can cause a
decrease in the efficiency of the CHC treatment, it is always important to make sure that the
vacuum leaks are corrected with the appropriate actions.

«
...
66
67
68
69
70
...
»

Summary of Contents for CHC Series



































































































































Reviews:

No comments