manualshive.com logo in svg

EcoWater CHC Series, Service And Troubleshooting Manual, Page: 24 / 130

Share
Download
EcoWater CHC Series Service And Troubleshooting Manual Download Page 24

24

4.0 TEST EQIPMENT and PPE

This section has been constructed to define the appropriate usage for a DVM (Digital Volt
Meter), Conductivity Pocket Meter ,Ultrasonic flow meter, other equipment as well as PPE
(Personal Protection Equipment) and Safety Practices.

4.0 Safety Requirements-

(Updated May, 2014)

THE SAFETY OF EcoWater CHC PERSONNEL MUST ALWAYS BE
TAKEN SERIOUSLY, AND DONE RIGHT WITHOUT REGARD
FOR TIME REQUIRED TO DO THE JOB SAFELY. YOUR LIFE
MAY DEPEND UPON IT!

EcoWater CHC REQUIRES you to follow all safety regulations as set forth by EcoWater management
and requires you to follow all training and or instruction you have been given by EcoWater. If you are
found not following this instruction, you will be warned only once, upon continued failure to follow
our requirements, you will be terminated.

All CHC Requirements are superseded by any Customer Safety Requirement. Before doing any work
at a Customer Site, you are required to check with the customer to obtain any training and/or safety
instructions that may pertain to your work.

You must follow these instructions at all times and are required to contact your supervisor, if any safety
requirements are not understood, or you will have any problems performing them.

EcoWater CHC has a Safety Board located in the Hallway to manufacturing for those personnel
working within our facility. This location includes the MSDS logs for those products used within our
facility. If any field personnel wishes, CHC will provide this same information for your review and or
use. It is your responsibility to acquire any MSDS sheets for products that were not provided by
EcoWater and use them. Please copy EcoWater on an MSDS sheets that you receive on chemicals
used on the behalf of EcoWater.

You must contain a working knowledge of the information found within this document, and be able to
show the ability to utilize this information at all times. This information will be covered within your
training regime at point of hire. You will also participate in yearly examinations and updates of your
working knowledge.

IF YOU HAVE ANY QUESTIONS OR CONCERNS CONTACT CARL STEFFEN AT cell 210-
857-5252.

Summary of Contents for CHC Series



































































































































Reviews:

No comments