Eaton i-on40H+ Administration And User Manual Download Page 60

Page: 60 / 67

User Menu Options

Page 56

HUA Function

Enables or disables the ability for remote controls to
generate Hold-Up Alarms (HUAs).

These options are described next.

Editing the programming of the buttons

You can use

System Config

– Remotes – Edit

to re-program the A, B or *

buttons on a one-way remote control

, or the “*” button on a two-way remote

control, after the devices have been assigned to a user.

A button can be programmed to:



Set a selected part set (in a partitioned system, it part sets only the

partition the remote control is assigned to).



Operate an output configured as "User Defined" by the installer.



Full set the whole system (one-way remote control only).



Unset the whole system (partitioned system, one-way remote control

only).



Full set or part set selected partitions (partitioned system, one-way

remote control only).



Unset selected partitions (partitioned system, one-way remote control

only).

Note for one-way remote controls:



If you have a part-setting (non-partitioned) system, you cannot

reprogram the unset button.



If you have a partitioned system, the unset button can only be used to

unset some or all partitions allocated to the user. See

Unset, Unset All

and

Unset, Partitions

below.

To re-program the buttons on a remote control:

Select

System Config

– Remotes – Edit

The following is displayed:




EITHER:

Press the button on the remote control you want to re-program.
Hold down the button until you see the transmit LED flash.

Summary of Contents for i-on40H+




































































Search results

Summary of Contents for i-on40H+

Reviews:

Related manuals for i-on40H+

Brands by name

Popular brands

Eaton i-on40H+, Administration And User Manual

Search results

Summary of Contents for i-on40H+

Reviews:

Related manuals for i-on40H+

Brands by name

Popular brands