Eaton i-on40H+ Administration And User Manual Download Page 3

Page: 3 / 67

Page iii

Contents

Compliance Statement ....................................................................... ii

Chapter 1: Introduction .......................................................... 1

About this manual ...................................................................1

Other publications ...................................................................1

About Users ...........................................................................2

User types ........................................................................................ 2

User access codes ............................................................................. 4

Code lockouts ................................................................................... 5

Installer access ................................................................................. 5

About part-setting and partitioned modes ...................................5

Part-setting mode ............................................................................. 5

Partitioned mode ............................................................................... 6

About the web interface ...........................................................7

Virtual Keypad .................................................................................. 8

Chapter 2: Setting and Unsetting ............................................ 9

Introduction ...........................................................................9

Using a keypad to set or unset the system ..................................9

Setting the system ............................................................................ 9

Quick-setting the system ................................................................. 12

Unsetting the system ....................................................................... 13

Using a two-way keyfob-style remote control ............................. 14

Operating the buttons ...................................................................... 15

Setting from a two-way remote control .............................................. 15

Unsetting from a two-way remote control........................................... 15

Querying the set/unset status from a two-way remote control .............. 16

Starting a hold-up alarm from a two-way remote control ..................... 16

Using a one-way remote control .............................................. 16

Setting from a one-way remote control .............................................. 17

Unsetting from a one-way remote control .......................................... 18

Using a one-way i-RK01 radio keypad ...................................... 18

Setting from an i-RK01 radio keypad ................................................. 18

Unsetting from an i-RK01 radio keypad .............................................. 19

Using a two-way KEY-RAS keypad ........................................... 19

Setting from a KEY-RAS radio keypad ................................................ 19

Unsetting from a KEY-RAS radio keypad............................................. 20

Using the SecureConnect™ app ............................................... 20

Chapter 3: Managing Alarms ................................................. 21

Alarm types and sounds ......................................................... 21

Other alarm actions ............................................................... 22

Speech messages ............................................................................ 23

Silencing, acknowledging and resetting alarms ........................... 24

Installer resets ............................................................................... 25

Accidental alarms.................................................................. 26

Viewing alerts ...................................................................... 26

Chapter 4: User Menu Options ............................................... 28

User Menu Map..................................................................... 28

Summary of Contents for i-on40H+




































































Search results

Summary of Contents for i-on40H+

Reviews:

Related manuals for i-on40H+

Brands by name

Popular brands

Eaton i-on40H+, Administration And User Manual

Search results

Summary of Contents for i-on40H+

Reviews:

Related manuals for i-on40H+

Brands by name

Popular brands