background image

From lab to production, 

providing a window into the process 

-19-

www.dynisco.com

Rev: n/a

P/N: n/a

ECO: n/a

Recording Mode   

 

Record Until Memory Used (Stop recording when full) or Continuous FIFO 

 

 

 

 

(First In - First Out - overwrites oldest data when full).

Recording Sample Interval  

From: Every 1; 2; 5; 10; 15; 30 Seconds, or Every 1; 2; 5; 10; 15; 30 Minutes.

Recorder Trigger   

 

The recording Start/Stop trigger method. From: Operation Mode; Recorder Menu;  

 

 

 

 

On Alarm; Digital Input

Trigger On Alarms 

 

Any from: Alarm n – Where n is alarms 1 to 5. Any combination of these can be set  

 

 

 

 

to trigger (TRG) or not (OFF).

Values To Record   

 

Any from: Process Variable value; Maximum or Minimum PV (since previous 

 

 

 

 

sample); Setpoint; Primary Power or Secondary Power.

Events To Record   

 

Any from: Alarm n Status or Unit On/Off. Note: An alarm state change between 

 

 

 

 

samples is also recorded. This uses additional recorder memory.

Recorder Status Information  

Shows if a recording is in progress; the recording mode; memory usage per sample;  

 

 

 

 

memory remaining and approximate recording time remaining.

Recorder Clock Configuration:

  

Refer to the Supplementary Product Manual for information about the additional screens when Data  

 

 

 

 

Recorder is fitted.

Date Format  

 

        w   The format used for displayed dates: dd/mm/yyyy (Day / Month / Year) or mm/dd/ 

 

 

 

 

yyyy (Month / Day / Year). – Recorder versions only.

Set Date  

 

        w   Sets the internal clock Date. – Entered in the format defined by Date Format screen.  

 

 

 

 

– Recorder versions only.

Set Day Of Week   

        w  Sets the day of week used by the internal clock. – Recorder versions only.

Set Time  

 

        w   Sets the internal clock Time. - In hh:mm:ss (Hours : Minutes : Seconds) format. 

 

 

 

 

– Recorder versions only.

Display Configuration:

Enable Custom Display Mode 

Enables/disables Custom Operation Mode, if configured 

 

 

 

 

(requires PC configuration software).

Read Only Operation Mode?  

Allows Operation Mode to be Read-Only or Read/Write. Screens can be seen but,  

 

 

 

 

values cannot be changed if Read-Only.

Operation Mode Bar Graph Format From: PID Power or Control Deviation or.

Trend Sample Interval  

 

Interval between display of next value on the trend graph From: Every 1; 2; 5; 10; 15;  

 

 

 

 

30 Seconds, or Every 1; 2; 5; 10; 15; 30 Minutes.

Select Trend Mode  

 

From: PV only, PV and SP or Max/Min PV between samples (candle-stick graph).  

 

 

 

 

Alarm activity is always shown.

Display Colour    

 

From: Red only; Green only; Red to Green on Alarm or Green to Red on Alarm.

Invert Display    

 

Standard or Negative display image.

Display Contrast    

 

Screen contrast (0 and 100) to improve clarity. 100 = maximum contrast.

Language  

 

 

Select English or the alternate local language. The alternate language type can be  

 

 

 

 

changed using the PC software.

Lock Code Configuration:

Lock Code View 1  

 

View and edit the Setup Wizard; Configuration Mode; Tuning Menu, Supervisor   

 

 

 

 

Mode, USB Menu and Recorder menu Lock Codes (1-9999 or OFF). 

 

 

 

 

Default Values = 10

Reset To Defaults:

Reset To Defaults  

 

Set all parameters to default values. Caution: User must reconfigure all required  

 

 

 

 

settings before using the instrument following a reset.

*Both Recorder Trigger state and Digital input selection must be the same to start recording

** Applies to Temperature control Only not pressure control.

Summary of Contents for ATC990
























Reviews: