background image

From lab to production, 

providing a window into the process 

-11-

www.dynisco.com

Rev: n/a

P/N: n/a

ECO: n/a

Operating Conditions (For Indoor Use)

Temperature:   

0°C to 55°C (Operating), –20°C to 80°C (Storage).

Relative Humidity:   20% to 95% non-condensing.

Supply Voltage and   Mains versions:  

 

100 to 240VAC ± 10%, 50/60Hz, 24VA.

 

 

 

Low voltage versions:   

20 to 48VC 50/60Hz 15VA or

 

 

 

 

 

 

 

22 to 65VDC 12W.

Conformance Norms

EMI:    

 

CE: Complies with EN61326.

Safety   

 

CE: Complies with EN61010-1. UL, cUL to UL61010C-1.

 

 

 

Pollution Degree 2, Installation Category II.

Front Panel Sealing:   To IP66 (IP65 front USB connector). IP20 behind the panel.

 

 

 

(IP rating not recognised / approved by UL).

Front Panel   

Wash with warm soapy water and dry immediately.

 

 

 

Close the USB cover (if fitted) before cleaning.

Display

Display Type:    

160 x 80 pixel, monochrome graphic LCD with a dual colour 

 

 

 

(red/green) backlight.

Display Area:    

66.54mm (W) x 37.42mm (H).

Display Characters:   0 to 9, a to z, A to Z, plus ( ) - and _

Trend View:    

120 of 240 data points shown in a scrollable window. Data is not

 

 

 

retained when power turned off or if time base is changed.

Trend Data:    

Any active alarm plus PV (solid) & SP (dotted) at sample time or

 

 

 

Max/Min PV between samples (candle-stick graph).

 

 

 

Auto scales from 2 to 100% of Input Span.

Trend Sample Rate:   1; 2; 5; 10; 15; 30 seconds or 1; 2; 5; 10; 15; 30 minutes.

Dimensions

Weight:  

 

0.65kg maximum.

Size:    

 

96 x 96mm (Front Bezel). 117mm (Depth Behind Panel).

Mounting Panel:  

Panel must be rigid. Maximum thickness 6.0mm (0.25inch).

Panel Cut-out Size:   92mm x 92mm. Tol0.5, -0.0mm.

Ventilation:   

20mm gap required above, below and behind.

Manufacturing Site

Address:  

 

The Hyde Business Park, Brighton, BN2 4JU, United Kingdom

Power:

Considerations:

Cleaning

Summary of Contents for ATC990
























Reviews: