Dynisco ATC770 Installation And Operation Manual Download Page 71

Page: 71 / 88

ATC770 Microprocessor-Based Pressure/Process Controller

Default value:

Process alarm.

ALARM 1 TYPE - Group 3

Available:

Only if A1.LNK is different than OFF.

Upper display: Selection of alarm 1 type.
Lower display: A1.TYP
Range:

HI, LO, InhIb. High, low, low with mask at start-up. For band alarm high means
outside band alarm, while low means inside band alarm.

Default value:

Low with mask at start-up.

ALARM 2 INPUT CHANNEL LINK - Group 3

Available:

Always.

Upper display: Configuration for alarm 2 selection.
Lower display: A2.LNK
Range:

OFF, ProC, band, deu. Disabled, process alarm, band alarm, deviation alarm.

Default value:

Process alarm.

ALARM 2 TYPE - Group 3

Available:

Only if A2.LNK is different from OFF.

Upper display: Selection of alarm 2 type.
Lower display: A2.TYP
Range:

HI, LO, InhIb. High, low, low with mask at start-up. For band alarm high means
outside band alarm, while low means inside band alarm.

Default value:

High.

ALARM 3 INPUT CHANNEL LINK - Group 3

Available:

Only if Alarm 3 output is fitted.

Upper display: Configuration for alarm 3 selection.
Lower display: A3.LNK
Range:

OFF, ProC, band, deu. Disabled, process alarm, band alarm, deviation alarm.

Default value:

Process alarm.

ALARM 3 TYPE - Group 3

Available:

Only if A3.LNK is different than OFF.

Upper display: Selection of alarm 3 type.
Lower display: A3.TYP
Range:

HI, LO, InhIb. High, low, low with mask start-up. For band alarm high means
outside band alarm, while low means inside band alarm.

Default value:

High.

Summary of Contents for ATC770

























































































Search results

Summary of Contents for ATC770

Reviews:

Related manuals for ATC770

Brands by name

Popular brands

Dynisco ATC770, Installation And Operation Manual

Search results

Summary of Contents for ATC770

Reviews:

Related manuals for ATC770

Brands by name

Popular brands