background image

74

COMMUNICATION BAUD RATE - Group 3

Available:

Only if SC.ADR is different than OFF.

Upper display: Baud rate.
Lower display: SC.BDR
Range:

600, 1200, 2400, 4800, 9600, 19200.

Default value:

19200.

LOADING DEFAULT DATA - Group 3

Available:

Only if access to level C is allowed.

Upper display: OFF
Lower display: DEFLT
Range:

Use 

 and 

 keys to switch the upper display from OFF to On 3, then press FUNC

key to load the default data of the parameters belonging to group 1, group 2 and
group 3.

11.4

G

ROUP

 4 P

ARAMETERS

SHUNT CALIBRATION - Group 4

Available:

Always.

Upper display: OFF if shunt calibration disabled, On if shunt calibration enabled.
Lower display: SHUNT
Range:

OFF, On.

Default value:

On.

SHUNT VALUE - Group 4

Available:

Only if SHUNT parameter is On.

Upper display: Shunt value.
Lower display: SHNT.%
Range:

From 40.0 to 100.0%

Default value:

80.0%.

PRESSURE INPUT FAIL SAFE - Group 4

Available:

Always.

Upper display: Pressure input fail safe condition.
Lower display: PI.IFS
Range:

HI, LO.

Default value:

High.

Summary of Contents for ATC770

























































































Reviews: