background image

•  Never look into the barrel or breech area of the NT11 when the marker 
  is switched on and able to fire.
•  Always fit a barrel blocking device to your NT11 when not in use on 
  the field of play.
•  The owner’s manual should always accompany the product for 
  reference or in the event of resale and new ownership.
•  Do not point the NT11 marker at anything that you do not intend 
  to shoot.
•  Do not shoot at people, animals, houses, cars or anything not related
  to the sport of paintball.
•  Do not fire the NT11 without the Boost™ bolt screwed in completely.
•  If you read these instructions and do not fully understand them or are
  unsure of your ability to make necessary adjustments properly, call 
  DYE or your local pro shop for help.

•  The NT11 marker is not a toy. Misuse may cause serious injury or death.
•  Please read, understand and follow the directions in the NT11 Owner’s
  manual. 
•  Eye protection that is designed specifically for paintball and meets 
  ASTM/CE standards must be worn by user and persons within range.
•  Recommend 18 years or older to purchase. Person under 18 must 
  have adult supervision.
•  Always treat the NT11 marker as if it were loaded and able to fire.
•  Only use compressed air or nitrogen gas in the NT11 marker. 
  DO NOT USE CO

2

.

•  Do not exceed 850 psi input pressure.
•  Ensure all air lines and fittings are tightened and secured before 
  gassing up the NT11.
•  Always chronograph the NT11 marker before playing paintball.
•  Never shoot the NT11 marker at velocities in excess of 300 feet per 

second, or at velocities greater than local or national laws allow.

W W W . D Y E P A I N T B A L L . C O M

W W W . D Y E P A I N T B A L L . C O M

2

3

W A R N I N G

IMPORTANT SAFETY INSTRUCTIONS AND GUIDELINES

W A R N I N G

IMPORTANT SAFETY INSTRUCTIONS AND GUIDELINES

Summary of Contents for NT11























Reviews: