background image

W W W . D Y E P A I N T B A L L . C O M

W W W . D Y E P A I N T B A L L . C O M

32

33

ON/OFF AIRPORT DETAIL

REMOVE THE AIRPORT LEVER AND INTERNAL CAM

• 

Remove the DYE sphere jewel located in the middle of the airport lever. 

•  Use a 1/16” Allen wrench to unscrew the retaining screw and remove the screw and lever. 
•  Insert a dental pick into the small slot to pull out the 

010 retaining O-ring

.

 If the Pin and Pin

  housing have been removed, the cam should come out with no resistance. If the Pin and    
  Housing are installed in the airport body, the cam must be in the ON position so it can
  be removed. 

INSTALL AIRPORT LEVER AND CAM

• 

Make sure that the Pin is not protruding into the area where the Cam sits. 

•  Use a dental pick or small Allen wrench to push the pin out of the bore if necessary. 
•  Drop the Cam into the airport body such that the slot face upwards and rotate it clockwise until  
  it drops in place and hits the internal stop. 
•  Insert the

 

010 retaining O-ring

 

into the groove and gently work it in place with a dental pick or  

  small screwdriver. 
•  Push the Lever into the Cam slot so that the Lever is facing down, or in the OFF position. 
•  Install the retaining screw with a 1/16” Allen wrench and tighten firmly. Turn the Lever counter- 
  clockwise until it hits the internal stop. Replace the jewel on the Retaining Screw so that the  
  Dye sphere is correctly oriented.

NOTE: For exploded view of airport and parts list see page 40.

ON/OFF AIRPORT DISASSEMBLY AND 
ASSEMBLY 

REMOVE PIN HOUSING ASSEMBLY

To disassemble the NT11 airport use the airport 
tool included on the DYE Multi-Tool included 
with the NT11. 
• Insert the airport tool into the Pin Housing and  
  turn counterclockwise 3-4 revolutions. Note 
  that the airport lever must be in the OFF
  position for the tool to grab the housing. 
Remove housing out of the airport body. 
• The pin and 

005 O-ring

 

may or may not come  

  out with the housing, if necessary use a pair  
  of needle-nosed pliers to pull the pin out and a  
  dental pick to remove the 

005 O-ring

.

INSTALL PIN HOUSING ASSEMBLY

•  

Coat the 

005 O-ring

 in lube and drop it into  

  the airport body. Use a 1/4” Allen wrench to  
 

  fully seat the O-ring in place by pushing gently on it. 
•  Insert the Pin into the Pin Housing from the backside. 
•  Place the housing onto the airport tool and insert the housing into the airport body. 
•  Turn clockwise until the Pin Housing fits snugly into the airport body.
*  If the airport tool is not available, a pair of needle-nose pliers can be used to unscrew the 
   Pin Housing. Just take care to not scratch or damage the threads or Pin Housing.

ON/OFF AIRPORT DETAIL

Summary of Contents for NT11























Reviews: