background image

PERFORMANCE & EFFICIENCY TUNING

From the factory the DYE NT11 is tuned to 
give you a maximum shooting comfort and 
consistency. If your playing conditions require 
high efficiency or you are playing indoors with 
lower velocity limits or you are using re-usable 
balls you can change the performance, feel 

and the efficiency of the NT11 by utilizing the supplied Bolt and 
volume inserts.  This will help you to tune your NT to your specific 
requirements and liking.

 

A factory tuned NT11 will yield about 1500 shots of a standard 68 Cubic 
Inch 4500psi tank. The operating pressure from factory is around 
125psi using no volume inserts and the green bolt flow insert.  This 
efficiency can be substantially increased by utilizing the supplied 

volume and bolt insert.  
 
The bolt flow inserts adjust how much and how fast of the chamber is used in each shot. The 
smallest insert is red, blue is the middle and and green one is the largest diameter one. The larger 
diameter the insert is the more gas is used out of the chamber on each shot before the self-
closing valve closes the chamber. This means that the operating pressure will be slightly lower 
with a larger insert but a little more gas is wasted. To increase the efficiency change the stock 
green insert to either the blue or the red one.
 
The volume inserts reduce the volume inside the NT11’s dump chamber (this is the amount of gas 
used for each individual shot). The green insert is the smallest reduction. This insert can be used 
at 300fps shooting when higher efficiency is required. The yellow and red inserts should be used 
when a slower than 300fps velocity is required.

W W W . D Y E P A I N T B A L L . C O M

W W W . D Y E P A I N T B A L L . C O M

21

20

PERFORMANCE & EFFICIENCY TUNING

It is also very important to have a good paint to barrel match with the NT11. This will cause a big 
difference in both the feel of the gun as well as the efficiency. A good paint fit is where you can 
barely blow the paintball through the barrel. If the balls roll through by themselves the fit is too 
loose. If paintballs are breaking inside the barrel when shot the fit is too tight.

The NT11 working pressure range is from 120psi to 150psi. Exceeding 150psi will cause leaking and 
eventually damage to the solenoid. Under 120psi operation can cause malfunction due to lack of 
force to move the bolt correctly. When increasing the efficiency by reducing the volume, the flow 
through the bolt or both and increasing the operating pressure you will notice slight increase in 
sound and recoil of the NT11.

NOTE: If you intend on using the NT11 at velocities lower than 250fps it is recommended to use 
the largest of the shot chamber inserts, and the blue Flow Insert in order to maintain suffi cient 
forces in the bolt for proper function.

Summary of Contents for NT11























Reviews: