DUROMAX DUAL FUEL XP12000DX Page 22 User Manual Download

Page: 22 / 76

Step 3 - Connect the Battery

GENERATOR SETUP (CONTINUED)

Remove the battery cover

Reinstall the battery plate

Cover the connected terminal with the black rubber

boot.
b.

Reinstall the battery cover plate using the wrench

from the toolkit.

Locate the negative cable

Locate the negative battery cable above and behind

the battery. One side is connected to ground and

the other end needs to be connected to the battery.

Route the free end to the negative battery terminal.

Connect the negative cable

Push the black rubber boot up the wire to expose

the connector.
b.

Securely connect the free end of the battery cable

to the negative battery terminal using the screw

and nut from the battery with the screwdriver and

wrench from the toolkit.

Remove the battery cover plate using the wrench

from the toolkit.

Summary of Contents for DUAL FUEL XP12000DX













































































Search results

Summary of Contents for DUAL FUEL XP12000DX

Reviews:

Related manuals for DUAL FUEL XP12000DX

Brands by name

Popular brands

DUROMAX DUAL FUEL XP12000DX, User Manual

Search results

Summary of Contents for DUAL FUEL XP12000DX

Reviews:

Related manuals for DUAL FUEL XP12000DX

Brands by name

Popular brands