DUROMAX DUAL FUEL XP12000DX Page 56 User Manual Download | Manualshive

Page: 56 / 76

background image

Emptying the Gas Tank

Shut fuel valve off

Remove fuel filter cup

Empty fuel filter cup

Turn the fuel valve to the “OFF” position.

Remove the fuel filter cup (see “Removing the Fuel Filter Cup”

earlier in this section.

Empty the fuel filter cup of any fuel.

1.

2.

3.

CAUTION

:

Do not store fuel from one season to another.

Gasoline sold at the pump today contains additives such
as ethanol that even when stored properly may damage
the fuel system components.

If you have been using gasoline in your generator; before

storing your generator for extended periods of time you
should drain your generator fuel tank of gasoline.

MAINTENANCE AND CARE (CONTINUED)

56

«
...
54
55
56
57
58
...
»

Summary of Contents for DUAL FUEL XP12000DX













































































Reviews:

No comments

Related manuals for DUAL FUEL XP12000DX

Brand: Durapac Pages: 11

Brand: Grundig Pages: 16

OLYMPUS JEFGENPET30EL

Brand: Jefferson Pages: 20

Brand: Olin Pages: 26

Brand: STEELE PRODUCTS Pages: 25

Brand: Caltta Pages: 10

LET'S GO PARTY 4 STUDIO

Brand: N-Gear Pages: 31

Brand: G-Power America Pages: 53

Brand: Ericsson Pages: 40

Guardian Ultra Source 004451-1

Brand: Generac Power Systems Pages: 24

Brand: Curtis Pages: 1

Brand: 70mai Pages: 42

Brand: PERFECTPRO Pages: 96

Brand: Dukane Pages: 126

Brand: Sunstech Pages: 48

Brand: Briggs & Stratton Pages: 6

Brand: Briggs & Stratton Pages: 28

Brand: Osotto Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands