DUROMAX DUAL FUEL XP12000DX Page 54 User Manual Download | Manualshive

Page: 54 / 76

background image

1.

2.

3.

SPARK PLUG

CONSULT MANUAL

BEFORE REMOVING

54

The spark plug is important for proper engine operation.
A good spark plug should be intact, free of deposits, and
properly gapped.

Improper maintenance may cause reduced fuel economy,

misfires, trouble starting, or damage to the spark plug

threads.

Spark Plug Maintenance

Remove spark plug cap

Remove spark plug

Inspect spark plug

Pull on the spark plug cap to remove it.

Unscrew the spark plug from the generator using the spark

plug wrench included with this product.

Visually inspect the spark plug.

MAINTENANCE AND CARE (CONTINUED)

«
...
52
53
54
55
56
...
»

Summary of Contents for DUAL FUEL XP12000DX













































































Reviews:

No comments

Related manuals for DUAL FUEL XP12000DX

Brand: Westinghouse Pages: 100

20KW Home Generator System

Brand: Briggs & Stratton Pages: 22

Brand: K&S BASIC Pages: 13

Brand: Motorola Pages: 82

Brand: Motorola Pages: 34

Brand: Motorola Pages: 28

Brand: Motorola Pages: 526

Brand: Motorola Pages: 29

Brand: Smarter tools Pages: 24

Brand: Smarter tools Pages: 25

Brand: A-iPower Pages: 2

Speaker Anywhere 200

Brand: Marmitek Pages: 44

Brand: Magnavox Pages: 2

Brand: MULTIPLEX modell Pages: 11

Brand: Briggs & Stratton Pages: 48

Brand: Keysight Pages: 50

Brand: Keysight Pages: 56

Brand: Abestorm Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands