DUROMAX DUAL FUEL XP12000DX User Manual Download

Page: 18 / 76

Propane Regulator w/

Hose

Used to provide a regulated

propane supply to the propane

inlet.

PACKAGE CONTENTS

Your generator comes with the items listed below. Please check to see that all of the following
items are included with your generator.

●

Note: Actual tools may differ in appearance or design from the image shown.

Double-Sided

Screw Driver

Oil Funnel w/ Hose

Spanner

Spark Plug Wrench

Plug Ends

Phillips and slot blade

screwdriver used for generator

maintenance.

Used to add oil to the

generator without messy spills.

Assorted wrenches used in

generator maintenance and

assembly. 10mm/12mm,

13mm/15mm, and

17mm/19mm.

Used in spark plug

maintenance, inspection, and

installation.

Plug heads for the receptacles

found on the generator are

included to make or rewire

your own cords.

Summary of Contents for DUAL FUEL XP12000DX













































































Search results

Summary of Contents for DUAL FUEL XP12000DX

Reviews:

Related manuals for DUAL FUEL XP12000DX

Brands by name

Popular brands

DUROMAX DUAL FUEL XP12000DX, User Manual

Search results

Summary of Contents for DUAL FUEL XP12000DX

Reviews:

Related manuals for DUAL FUEL XP12000DX

Brands by name

Popular brands