DUROMAX DUAL FUEL XP12000DX Page 16 User Manual Download

Page: 16 / 76

GENERATOR COMPONENTS

4. Fuel Tank

2. Air Cleaner

6. Handles

7. Battery

8. Oil Fill and Dipstick

1. Recoil Start

5. Power Panel

3. Fuel Valve

13. Low Oil Alert

21. GFCI 20A Receptacles

Recoil Start

– Easy pull recoil start to start the engine without the electric start.

Air Cleaner

- A removable, cleanable, oiled, element that cleans the air going into the engine.

Fuel Valve

- On/Off valve that allows gasoline to the fuel switch.

Fuel Tank

- All metal 8.3 gallon gasoline fuel tank.

Power Panel

- Contains the start switch, plugs, meters, and circuit breakers.

Handles

- Longest handles of any DuroMax model allow easy movement across any surface

Battery

- 12V DC battery that powers the electric start system.

Oil Fill and Dipstick

- Use to add or check the oil.

Fuel Switch -

Fuel selection switch to choose Gas, Propane, or Storage mode.

10.

Propane Inlet

- Provides a regulated LPG fuel supply to the engine. (Intended for use with an

LPG source of 3 PSI or more.)

11.

Engine Switch

– 3 Position switch to “Start”, “Run”, or turn “Off” the generator.

12.

Charging Light

- Will light when the generator is charging the on-board battery.

Summary of Contents for DUAL FUEL XP12000DX













































































Search results

Summary of Contents for DUAL FUEL XP12000DX

Reviews:

Related manuals for DUAL FUEL XP12000DX

Brands by name

Popular brands

DUROMAX DUAL FUEL XP12000DX, User Manual

Search results

Summary of Contents for DUAL FUEL XP12000DX

Reviews:

Related manuals for DUAL FUEL XP12000DX

Brands by name

Popular brands