Duplo DSF-2000 Instruction Manual Download Page 12

Page: 12 / 64

Paper feeder B

Paper feed tray B

Stack guide B

Sub guide B

Reference guide B

Separator air
adjustment knob B

Separator adjustment
knob B

Separator air duct B

Separator B

Suction belt B

Level sensor B

Shutter B

Upper door

Lower door

Lower door release
lever

Bridge

Bridge door

Bridge cable

Ejection guide

Power cord

D-PORT 1 connector

D-PORT 2 connector

Connector 1

Connector 2

Remote switch

Main power switch

Used to insert cover paper.

Stacks cover paper.

Holds the edge of cover paper stacked on the paper feed tray B, and maintains
the position.

Holds the edge of conveyed cover paper to prevent deviation of cover paper.

Press cover paper against this when stacking.

Knob for adjusting the position of the shutter B to adjust the amount of separator
air blown out.

Knob for adjusting the position of the separator B.

Blows out air to separate cover paper stacked on the paper feed tray B.

Prevents double-feeding at the paper feeder B.

Sucks and conveys cover paper.

Sensor which determines the position of the cover paper raised by the
separator air. Adjusted using a knob.

For adjusting the amount of air blown out to separate paper by covering the
separator air duct B.

Open when correcting jams.

Pull up to open the lower door.

Feeds paper to the downstream processing unit.

Open when paper jams at the bridge.

Connect to this unit.

Finely adjusts the paper ejection height by changing the angle.

Connect to an outlet.

Normally not used.

Connector for connecting the connecting cable from a downstream processing
unit such as the DBM-120 Sheet by Sheet.

Connector for connecting the connecting cable from a downstream processing
unit such as the DBM-400 Sheet by Sheet.

Connector for optional devices. Normally not used.

Refer to “5-1. Turning ON the Power”.

3. NAMES AND OPERATION OF PARTS

No.

Name

Operation

Summary of Contents for DSF-2000

































































Search results

Summary of Contents for DSF-2000

Reviews:

Brands by name

Popular brands

Duplo DSF-2000, Instruction Manual

Search results

Summary of Contents for DSF-2000

Reviews:

Brands by name

Popular brands