Duplo DF-990 Instruction Manual Download

Page: 85 / 100

Chapter 5 Cleaning the Machine

Chapter 5 Cleaning the Machine

• Make sure that you disconnect the power cord from the wall outlet before cleaning.
• Before you use the machine after cleaning, make sure that its surface is completely dry.

Do not use flammable sprays and solvents during cleaning, etc. of internal

parts of the machine and in the vicinity of the machine.

Doing so could cause build-up of gas inside the machine, which in turn could

cause ignition, resulting in fire and explosion.

When using alcohol, exercise precaution against fire and ventilate well, and

after use, store in a safe place.

Use of other solvents may damage the rubber rollers and resin inside the machine,

resulting in malfunction.

Open or close the top cover

gently.

Hands or fingers may be caught in the

cover section. Doing so may result in

injury.

Cleaning paper feed rings and folding rollers

Open the top cover.

Paper feed ring

Clean with a cloth moistened with alcohol

rotating the paper feed ring by hand.

Folding roller

Remove the folding plate 1.

Clean with a cloth moistened with

alcohol rotating the jam correction

knob.

Summary of Contents for DF-990





































































































Search results

Summary of Contents for DF-990

Reviews:

Related manuals for DF-990

Brands by name

Popular brands

Duplo DF-990, Instruction Manual

Search results

Summary of Contents for DF-990

Reviews:

Related manuals for DF-990

Brands by name

Popular brands