Duplo DF-990 Instruction Manual Download

Page: 63 / 100

Chapter 3 Advanced Operation

6-2. Adjusting stacker roller position

During cross folding or when folding thick

paper, adjust the position of the stacker roller

in cases when the paper is opened when

ejected causing misalignment or when a paper

jam occurs in the paper ejecting section.

Do not move the stacker roller forcibly back

and forth by hand. The machine may be

broken by doing so.

Guide for the setting position of stacker roller

Settings

Applicable standard paper size and folding mode

For EU

For NA

Double fold

STMT,

INV

Double fold, Letter fold, Accordion-fold

Double fold, Letter fold, Accordion-fold,

Gate fold

Double fold

LTR

Double fold

Accordion-fold, Gate fold

Gate fold

A3, B4

Double fold

STMT,

INV

Single fold, Irregular accordion fold-out,

Gate fold

Letter fold, Accordion-fold

LTR

Letter fold, Accordion-fold

Letter fold

LGL,

LGR

Double fold

A5, B6

Single fold, Irregular accordion fold-out

Gate fold

LTR

Gate fold

Letter fold, Accordion-fold

LGL

Letter fold, Accordion-fold

Single fold, Irregular accordion fold-out

Letter fold, Accordion-fold

LTR

Single fold, Irregular accordion fold-out

LGR

Letter fold, Accordion-fold

A3, B4

Single fold, Irregular accordion fold-out,

Gate fold

LGL,

LGR

Single fold, Irregular accordion fold-out,

Gate fold

When sheets of paper folded in the gate fold mode unfold and a sheet

processed later slips into the one processed before:

Depending on the type and size of paper,

the adjustable range in the gate fold mode is

limited. Be sure to decrease the setting values

one scale at a time in this mode and check the

results.

Touch the

key on the [Ready]

screen.

The [Fold Position] screen is displayed.

Summary of Contents for DF-990





































































































Search results

Summary of Contents for DF-990

Reviews:

Related manuals for DF-990

Brands by name

Popular brands

Duplo DF-990, Instruction Manual

Search results

Summary of Contents for DF-990

Reviews:

Related manuals for DF-990

Brands by name

Popular brands