Duplo DF-990 Instruction Manual Download

Page: 57 / 100

Chapter 3 Advanced Operation

4-1-2. Adjustment of the parts

Do not touch the power switch

with wet hands.

Otherwise electric hazards may occur.

Turn off the power switch.

Otherwise electric hazards

may occur.

Do not touch the power

plug with wet hands.

Disconnect the power plug from the

outlet.

Take the T-handle hexagonal wrench.

Open or close the top cover

gently.

Hands or fingers may be caught in the

cover section. Doing so may result in

injury.

Open the top cover.

Screw

Loosen the screw of the auxiliary paper

feed ring (for moving) using the T-

handle hexagonal wrench, accessory

part.

Do not use the T-handle hexagonal wrench

for a purpose other than handling the

auxiliary paper feed ring as instructed in

this manual.

Do not disassemble the product
more than needs.

Fire, electrification, injury, malfunction,

or breakdown may be caused by

disassembling the parts which are not

specified in this manual.

Move the auxiliary paper feed ring.

Move the auxiliary paper feed ring so that it will be on the folding line of the paper.

Tighten the screw loosened.

Store the T-handle hexagonal wrench in the original position after adjustment the auxiliary paper feed

ring.

Summary of Contents for DF-990





































































































Search results

Summary of Contents for DF-990

Reviews:

Related manuals for DF-990

Brands by name

Popular brands

Duplo DF-990, Instruction Manual

Search results

Summary of Contents for DF-990

Reviews:

Related manuals for DF-990

Brands by name

Popular brands