manualshive.com logo in svg

Duplo DF-990, Instruction Manual

Share
Download
Duplo DF-990 Instruction Manual Download Page 13

9

Chapter 1 Before Operation

Copyright © 2019 Duplo Corporation All Rights Reserved

No.

Name

Function

[3]

Side cover

Safety cover to prevent the user from touching the moving parts.

[4]

Power inlet

Connector for the power cord.

[5]

Support paper feed tray

For ensuring paper are stacked on the paper feed tray properly.

[6]

Paper feed tray

For stacking the paper to be folded.

[7]

Top cover

Safety cover to prevent the user from touching the moving parts. The top 

cover keeps hands or fingers from being caught and injured by braking the 

opening or closing motion.

[8]

Folding plate 1

Guide plate for deciding the paper folding position.

[9]

Folding plate 2

[10]

Paper set lever  

(DF-990/DF-990A)

This lever is used to move the paper feed tray up and down when stacking 

paper.

3-2.  Internal parts (Paper ejecting section)

[1]

[5]

[3]

[4]

[6]

[7]

[2]

No.

Name

Function

[1]

Stacker lever

This is the lever that supports the stacker roller. The height of the roller can 

be adjusted.

[2]

Ejecting section

For receiving folded paper ejected out.

[3]

Paper receiving tray

For stacking ejected paper.

[4]

Stacker belt

For ejecting folded paper.

[5]

Stacker roller

It holds down the ejected paper and supports conveyance of paper.

[6]

Auxiliary paper ejection guide

Used to hold the ejected paper.

[7]

Paper support guide

A4/LT size fine quality paper of 64 g/m

2

 /43.52 lbs, 81.4 g/m

2

 /55.35 lbs will 

be well in alignment by using this paper support guide at the time of paper 

ejection for letter fold or accordion fold.

Summary of Contents for DF-990





































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands