Duplo DF-990 Instruction Manual Download

Page: 81 / 100

Chapter 4 Using the DF HAND FEED KIT

20 mm/

0.78 inch or less

Reverse side

of paper

Paper feed direction

Stitching position is within 20 mm/0.78 inch or

less from the edge of paper.

When the upper-left corner of the paper is

stitched with the stapler, reverse the paper,

and insert the paper into the inlet so that

the staples will be positioned at the top

right corner.

Stitching position with staples and folding style are as shown in the figure.

Reverse side

of paper

Single fold

Letter fold

: Staple (reverse side)

: Staple (front side)

Paper

feed

direction

Ejection

direction

Accordion-fold

3. Manual Feed Mode Setting

Displayed only when DF HAND FEED KIT is registered as an optional item.

Touch the

key on the top screen —> Touch the

key —> Touch the [Manual

Feed Mode].

The [Manual Feed Mode] screen is displayed.

[3]

[5]

[4]

[2]

[1]

No.

Name

Function

Default

value

[1]

M-Feed Mode

Set on/off of the manual feed mode.

Off

[2]

Timing

Sets the time from insertion of paper into the manual feed inlet to

starting of the folding operation.

Normal

[3]

Size

Sets the paper size to be inserted manually.

[4]

(Return) key

Saves the manual feed mode setting and returns to the [Function

Settings] screen.

–

[5]

(Cancel) key

Returns to the [Function Settings] screen without saving the input

content.

Press and hold to return to the [Ready] screen.

–

Summary of Contents for DF-990





































































































Search results

Summary of Contents for DF-990

Reviews:

Related manuals for DF-990

Brands by name

Popular brands

Duplo DF-990, Instruction Manual

Search results

Summary of Contents for DF-990

Reviews:

Related manuals for DF-990

Brands by name

Popular brands