1.6 Operation
Read this entire Manual before you start running the
machine for the fi rst time. Pay special attention to the
safety instructions (section 2 below).
Note!
The operating procedure described below is
illustrated in the convenient “Daily Operation Guide”
on page 2.
Turn on the machine and allow it to heat up (see
sections 1.4 and 1.5). You are now ready to start sealing
trays, as follows:
1
Put the fi lled tray in the cassette.
2
Pull the fi lm over the tray.
3
Pull down the sealing lid, using the fully open handle.
4
Turn the handle downwards to lock lid.
5
Wait for 2 - 5 seconds to pass in order for
sealing to be fi nished.
6
Turn handle to its original position, open lid and
remove
tray.
If the tray leaks along the edges of the sealed tray, try
raising the temperature (see section 1.5) by 10°C. If it still
leaks, raise the temperature another 10°C at a time (max
175°C) or increase the sealing time. If the fi lm is hard to
pull off or breaks when opening, lower the sealing time
or the sealing temperature.
When the machine is not used, turn it off with the
switch, remove the cassette, close and lock the lid.
Operator safety
Study this entire Instruction Manual before starting to
use your DF 10/DF 15. Please note that all electrical
units, if used incorrectly, can cause fi res, electrical shocks
and/or personal injury. Always follow these Instructions
carefully to minimize the risk of accidents.
No emergency stop device is needed thanks to the safe
machine construction.
As the temperature of the heating plate is normally 100-
175°C, there is a risk of burn injury under the sealing lid.
Always handle with due caution.
Safety
2.1
This machine fulfi lls stringent Swedish health and safety
requirements (AFS 1994:48) as well as the corresponding
EC-directives. A safety analysis is available upon request
from Duni AB.
In case of malfunction, fi rst check the FAQ and Trouble-
shooting guidelines (sections 4 and 5 in this Manual).
If the problem persists, contact your local dealer.
Machine safety
The machine is equipped with an overheat switch (18),
which stops the heating in case of an error in the
temperature regulator.
Always unplug the machine before cleaning or
maintenance!
2.
2.2
6
Manual DF10 Alla-marg.indd 38
Manual DF10 Alla-marg.indd 38
2011-11-28 14.00
2011-11-28 14.00
1.6 Operation
Read this entire Manual before you start running the
machine for the fi rst time. Pay special attention to the
safety instructions (section 2 below).
Note!
The operating procedure described below is
illustrated in the convenient “Daily Operation Guide”
on page 2.
Turn on the machine and allow it to heat up (see
sections 1.4 and 1.5). You are now ready to start sealing
trays, as follows:
1
Put the fi lled tray in the cassette.
2
Pull the fi lm over the tray.
3
Pull down the sealing lid, using the fully open handle.
4
Turn the handle downwards to lock lid.
5
Wait for 2 - 5 seconds to pass in order for
sealing to be fi nished.
6
Turn handle to its original position, open lid and
remove
tray.
If the tray leaks along the edges of the sealed tray, try
raising the temperature (see section 1.5) by 10°C. If it still
leaks, raise the temperature another 10°C at a time (max
175°C) or increase the sealing time. If the fi lm is hard to
pull off or breaks when opening, lower the sealing time
or the sealing temperature.
When the machine is not used, turn it off with the
switch, remove the cassette, close and lock the lid.
Operator safety
Study this entire Instruction Manual before starting to
use your DF 10/DF 15. Please note that all electrical
units, if used incorrectly, can cause fi res, electrical shocks
and/or personal injury. Always follow these Instructions
carefully to minimize the risk of accidents.
No emergency stop device is needed thanks to the safe
machine construction.
As the temperature of the heating plate is normally 100-
175°C, there is a risk of burn injury under the sealing lid.
Always handle with due caution.
Safety
2.1
This machine fulfi lls stringent Swedish health and safety
requirements (AFS 1994:48) as well as the corresponding
EC-directives. A safety analysis is available upon request
from Duni AB.
In case of malfunction, fi rst check the FAQ and Trouble-
shooting guidelines (sections 4 and 5 in this Manual).
If the problem persists, contact your local dealer.
Machine safety
The machine is equipped with an overheat switch (18),
which stops the heating in case of an error in the
temperature regulator.
Always unplug the machine before cleaning or
maintenance!
2.
2.2
6
Manual DF10 Alla-marg.indd 38
Manual DF10 Alla-marg.indd 38
2011-11-28 14.00
2011-11-28 14.00
1.6 Operation
Read this entire Manual before you start running the
machine for the fi rst time. Pay special attention to the
safety instructions (section 2 below).
Note!
The operating procedure described below is
illustrated in the convenient “Daily Operation Guide”
on page 2.
Turn on the machine and allow it to heat up (see
sections 1.4 and 1.5). You are now ready to start sealing
trays, as follows:
1
Put the fi lled tray in the cassette.
2
Pull the fi lm over the tray.
3
Pull down the sealing lid, using the fully open handle.
4
Turn the handle downwards to lock lid.
5
Wait for 2 - 5 seconds to pass in order for
sealing to be fi nished.
6
Turn handle to its original position, open lid and
remove
tray.
If the tray leaks along the edges of the sealed tray, try
raising the temperature (see section 1.5) by 10°C. If it still
leaks, raise the temperature another 10°C at a time (max
175°C) or increase the sealing time. If the fi lm is hard to
pull off or breaks when opening, lower the sealing time
or the sealing temperature.
When the machine is not used, turn it off with the
switch, remove the cassette, close and lock the lid.
Operator safety
Study this entire Instruction Manual before starting to
use your DF 10/DF 15. Please note that all electrical
units, if used incorrectly, can cause fi res, electrical shocks
and/or personal injury. Always follow these Instructions
carefully to minimize the risk of accidents.
No emergency stop device is needed thanks to the safe
machine construction.
As the temperature of the heating plate is normally 100-
175°C, there is a risk of burn injury under the sealing lid.
Always handle with due caution.
Safety
2.1
This machine fulfi lls stringent Swedish health and safety
requirements (AFS 1994:48) as well as the corresponding
EC-directives. A safety analysis is available upon request
from Duni AB.
In case of malfunction, fi rst check the FAQ and Trouble-
shooting guidelines (sections 4 and 5 in this Manual).
If the problem persists, contact your local dealer.
Machine safety
The machine is equipped with an overheat switch (18),
which stops the heating in case of an error in the
temperature regulator.
Always unplug the machine before cleaning or
maintenance!
2.
2.2
6
Manual DF10 Alla-marg.indd 38
Manual DF10 Alla-marg.indd 38
2011-11-28 14.00
2011-11-28 14.00
1.6 Operation
Read this entire Manual before you start running the
machine for the fi rst time. Pay special attention to the
safety instructions (section 2 below).
Note!
The operating procedure described below is
illustrated in the convenient “Daily Operation Guide”
on page 2.
Turn on the machine and allow it to heat up (see
sections 1.4 and 1.5). You are now ready to start sealing
trays, as follows:
1
Put the fi lled tray in the cassette.
2
Pull the fi lm over the tray.
3
Pull down the sealing lid, using the fully open handle.
4
Turn the handle downwards to lock lid.
5
Wait for 2 - 5 seconds to pass in order for
sealing to be fi nished.
6
Turn handle to its original position, open lid and
remove
tray.
If the tray leaks along the edges of the sealed tray, try
raising the temperature (see section 1.5) by 10°C. If it still
leaks, raise the temperature another 10°C at a time (max
175°C) or increase the sealing time. If the fi lm is hard to
pull off or breaks when opening, lower the sealing time
or the sealing temperature.
When the machine is not used, turn it off with the
switch, remove the cassette, close and lock the lid.
Operator safety
Study this entire Instruction Manual before starting to
use your DF 10/DF 15. Please note that all electrical
units, if used incorrectly, can cause fi res, electrical shocks
and/or personal injury. Always follow these Instructions
carefully to minimize the risk of accidents.
No emergency stop device is needed thanks to the safe
machine construction.
As the temperature of the heating plate is normally 100-
175°C, there is a risk of burn injury under the sealing lid.
Always handle with due caution.
Safety
2.1
This machine fulfi lls stringent Swedish health and safety
requirements (AFS 1994:48) as well as the corresponding
EC-directives. A safety analysis is available upon request
from Duni AB.
In case of malfunction, fi rst check the FAQ and Trouble-
shooting guidelines (sections 4 and 5 in this Manual).
If the problem persists, contact your local dealer.
Machine safety
The machine is equipped with an overheat switch (18),
which stops the heating in case of an error in the
temperature regulator.
Always unplug the machine before cleaning or
maintenance!
2.
2.2
6
Manual DF10 Alla-marg.indd 38
Manual DF10 Alla-marg.indd 38
2011-11-28 14.00
2011-11-28 14.00