![background image](http://html1.mh-extra.com/html/ducati/manual-slide/manual-slide_user-manual_2537586014.webp)
14
The connecting cables to the battery are already provided with the card.
Caution!
Respect the polarity of the connection cables to the battery ( + and -).
Caution:
The battery must be connected to the board at full charge level. Before connection and use, the battery
should be put under charge for a minimum of 16 hours.
To charge the battery:
a) you can connect the battery to the circuit board (CTH46) and use a socket, connecting it to the terminals of
the high voltage connection which are located upstream of the transformer.
b) we recommend the use of the optional accessory MP037: witch is a independant battery charger with charging
control system. You can use other 12V battery chargers, but make sure they are provided with a charging
control system to avoid irreparable damage to the battery.
The solar panel is fastened to the wall with the appropriate arc provided with it. FIG.18 . T
The tilt angle of the arc is already calculated based on the parallel Earth’s center of Europe. The panel should
be facing South and should be avoided at any shadow that may limit the radiation on the same. Clean the panel
from any dirt, leaves or snow witch could obscure it.
The greater the exposure of the panel to sunlight, the greater will be the level of daily stored energy.
The greater the light, the higher the level of stored energy. It is possible to add extra solar panels by parallel
connection.
In order to charge the battery, the solar panel must deliver a voltage greater than 13V.
11. PRoVISIonAL ADJUSTMEnT oF THE MAgnETIC LIMITS
The position of the magnetic limits determines the stroke of the gate opening and closing.
WARnIng:
It is important that the magnets are positioned so that they are detected before the gate touches the
mechanical stops of the gate.
For a perfect adjustment of the final position of the end stops proceed in two stages.
Before final fixing, place the magnets momentarily to 10 cm before the desired final stop position of the gate in
order to make sure that the magnet is detected before the gate touches the mechanical stop. FIG.10 -12
Pre- position of magnetic limit for closed position:
1) Unlock the motor
2) Place the leaf to 10 cm before the desired closed position.
3) Manually move the magnetic limit (M) up to align it with the magnet reeder “ Reed “ (R ). FIG. 8-10
4) Verify that the yellow LED turns on the electronic board to confirm that the magnet is detected by the electronic
board.
Pre-position of magnetic limit for open position:
2) Place the leaf to 10 cm before the desired closed position.
3) Manually move the magnetic limit (M) up to align it with the magnet reeder “ Reed “ (R ). FIG. 8-10
4) Verify that the yellow LED turns on the electronic board to confirm that the magnet is detected by the electronic
board.
12. REMoTE ConTRoL
CODE IN THE ELECTRONIC BOARD - MEMORIZE THE CODE IN THE ELECTRONIC BOARD
CAUTION: Before you begin:
1) Unlock the motor, place the gate halfway
2) Lock the engine.
Radio Transmitters:
Models: 6203ROL; 6203 / P = 2-channels radio rolling code remotes control (over 3 billion combinations)
Models: 6204; 6206 = 4-channels radio rolling code remotes control (over 3 billion combinations)
A) Save the radio control electronic board in automation.
1 - press the P1 button on the electronic board FIG.16 - 17 / A
2 - release the button P1
3 - press on the radio remote control, the button corresponding to the channel that you want to synchronize
with the drive ( you may need to hold the button for about 4-5 seconds or even re- press it until the automation
recognizes and stores the remote control code). When the red LED will flash for 3/4 times the remote control
has been store.
4 - to activate your gate, press the remote control button previously synchronized.
The gate will open by and will stop as the magnetical limit (M) is detected by the reeder (R).