DSPPA PC1021X User Manual Download Page 4

Page: 4 / 26

* *

8 Channel Amplifier Matrix Controller

CONTENTS

................................................................................................................................. 1

1.1 BRIEF INTRODUCTION ............................................................................................................................................ 1

1.2 PERFORMANCE ...................................................................................................................................................... 1

B. APPEARANCE DESCRIPTION

.......................................................................................................................... 2

2.1 DESCRIPTION OF FRONT PANEL ............................................................................................................................. 2

2.2 DESCRIPTION OF REAR PANEL ................................................................................................................................ 3

C. LINKAGE INSTRUCTION

.................................................................................................................................. 4

3.1 SYSTEM CONNECTION DIAGRAM ........................................................................................................................... 4

D. INTERFACE INSTRUCTIONS

........................................................................................................................... 5

4.1 START-UP ............................................................................................................................................................... 5

4.2 MAIN INTERFACE INSTRUCTIONS ........................................................................................................................... 5

4.3 INTERFACE OPERATION INSTRUCTIONS.................................................................................................................. 7

(1)

YSTEM SETTINGS

.............................................................................................................................................. 7

(2)

QUALIZER AND MASTER VOLUME SETTINGS

..................................................................................................... 8

(3)

UDIO OUTPUT LEVEL SETTINGS

........................................................................................................................ 9

................................................................................................. 9

(5)

AIN AND STANDBY AMPLIFIER SWITCH SETTINGS AND MANUAL CALL SETTINGS

............................................ 10

Main and standby amplifier switch settings .................................................................................................... 10

Manual call settings of main and standby amplifiers ...................................................................................... 11

(6)

ONE LOAD SETTINGS

....................................................................................................................................... 18

(7)

OUCH SCREEN CALIBRATION

........................................................................................................................... 19

SAFETY PRECAUTIONS

....................................................................................................................................... 20

PACKING LIST

....................................................................................................................................................... 21

SPECIFICATIONS

.................................................................................................................................................. 21

Summary of Contents for PC1021X



























Search results

Summary of Contents for PC1021X

Reviews:

Related manuals for PC1021X

Brands by name

Popular brands

DSPPA PC1021X, User Manual

Search results

Summary of Contents for PC1021X

Reviews:

Related manuals for PC1021X

Brands by name

Popular brands