manualshive.com logo in svg

DSE DSE7560, Manual

Share
Download
DSE DSE7560 Manual Download Page 58

DSE Model 7560MK1 Main Control and ATS Operators Manual 

 

                                      057-015   7560MK1 OPERATING MANUAL ISSUE 10    10/02/09  

AM  

58

9.3  ENCLOSURE CLASSIFICATIONS  
 

IP CLASSIFICATIONS

  

 

BS EN 60529 Degrees of protection provided by enclosures 

 

First Digit

 

Second digit

 

Protection against contact and ingress of solid objects

 

Protection against ingress of water

 

0

 

No protection

 

0

 

No protection

 

1

 

Protected against ingress solid objects with a 
diameter of more than 50 mm. No protection against 
deliberate access, e.g. with a hand, but large surfaces 
of the body are prevented from approach.

 

1

 

Protection against dripping water falling vertically. No 
harmful effect must be produced (vertically falling drops).

 

2

 

Protected against penetration by solid objects with a 
diameter of more than 12 mm. Fingers or similar 
objects prevented from approach.

 

2

 

Protection against dripping water falling vertically. There 
must be no harmful effect when the equipment (enclosure) 
is tilted at an angle up to 15° from its normal pos ition 
(drops falling at an angle).

 

3

 

Protected against ingress of solid objects with a 
diameter of more than 2.5 mm. Tools, wires etc. with a 
thickness of more than 2.5 mm are prevented from 
approach.

 

3

 

Protection against water falling at any angle up to 60° 
from the vertical. There must be no harmful effect (spray 
water).

 

4

 

Protected against ingress of solid objects with a 
diameter of more than 1 mm. Tools, wires etc. with a 
thickness of more than 1 mm are prevented from 
approach.

 

4

 

Protection against water splashed against the equipment 
(enclosure) from any direction. There must be no harmful 
effect (splashing water).

 

5

 

Protected against harmful dust deposits. Ingress of 
dust is not totally prevented but the dust must not enter 
in sufficient quantity to interface with satisfactory 
operation of the equipment. Complete protection 
against contact.

 

5

 

Protection against water projected from a nozzle against 
the equipment (enclosure) from any direction. There must 
be no harmful effect (water jet).

 

6

 

Protection against ingress of dust (dust tight). 
Complete protection against contact.

 

6

 

Protection against heavy seas or powerful water jets. 
Water must not enter the equipment (enclosure) in harmful 
quantities (splashing over).

 

  

Summary of Contents for DSE7560































































Reviews:

No comments

Brands by name

Popular brands

Load more brands