manualshive.com logo in svg

DSE DSE7560, Manual

Share
Download
DSE DSE7560 Manual Download Page 14

DSE Model 7560 ATS and Mains Controller Operators Manual 

14      057-017    7560 OPERATING MANUAL ISSUE 10.2 10/02/09  AM  

 

 

3.11  APPLICABLE STANDARDS 

 
BS 4884-1 

This document conforms to BS4884-1 1992 Specification for presentation 
of essential information. 

BS 4884-2 

This document conforms to BS4884-2 1993 Guide to content 

BS 4884-3 

This document conforms to BS4884-3 1993 Guide to presentation 

BS EN 60068-2-1 
 (Minimum 
temperature) 

-30

°

C (-22

°

F) 

BS EN 60068-2-2 
 (Maximum 
temperature) 

+70

°

C (158

°

F) 

BS EN 60950  

Safety of information technology equipment, including electrical business 
equipment 

BS EN 61000-6-2  

EMC Generic Immunity Standard (Industrial) 

BS EN 61000-6-4  

EMC Generic Emission Standard (Industrial) 

BS EN 60529  
(Degrees of protection 
provided by 
enclosures) 

IP65 (front of module when installed into the control panel with the 
supplied sealing gasket)  
IP42 (front of module when installed into the control panel WITHOUT 
being sealed to the panel) 

UL508  
NEMA rating 
(Approximate) 

12 (Front of module when installed into the control panel with the supplied 
sealing gasket).  
2 (Front of module when installed into the control panel WITHOUT being 
sealed to the panel) 

IEEE C37.2 
(Standard Electrical 
Power System Device 
Function Numbers and 
Contact Designations) 

Under the scope of IEEE 37.2, function numbers can also be used to 
represent functions in microprocessor devices and software programs. 
The 7000 series controller is device number 11L-7000 (Multifunction 
device protecting Line (generator) – 7000 series module).  
 
As the module is configurable by the generator OEM, the functions 
covered by the module will vary. Under the module’s factory configuration, 
the device numbers included within the module are : 
 
2 – Time delay starting or closing relay 
27AC – AC undervoltage relay 
27DC – DC undervoltage relay 
30 – annunciator relay 
42 – Running circuit breaker 
50 – instantaneous overcurrent relay 
51 – ac time overcurrent relay 
52 – ac circuit breaker 
59AC – AC overvoltage relay 
59DC – DC overvoltage relay 
62 – time delay stopping or opening relay 
74– alarm relay 
81 – frequency relay 
86 – lockout relay 

 

In line with our policy of continual development, Deep Sea Electronics, reserve the right to change specification without notice. 

Summary of Contents for DSE7560































































Reviews:

No comments

Brands by name

Popular brands

Load more brands