manualshive.com logo in svg

DSE DSE7560, Manual

Share
Download
DSE DSE7560 Manual Download Page 30

DSE Model 7560 ATS and Mains Controller Operators Manual 

30      057-017    7560 OPERATING MANUAL ISSUE 10.2 10/02/09  AM  

 

 
CLOSE MAINS 
This push button is used to control the closure of the mains load switching 
device and has two modes of operation : 
1.  Synchronising is NOT enabled. Pressing this button when the mains  is 

available off load and in MANUAL mode, the bus load switch is opened 
and the mains load switch is closed. Further presses of this button will 
have no effect. 

2.  Synchronising is enabled. Pressing this button when the mains  is 

available  and in MANUAL mode, the 7510MK1 controller, will volts 
match and synchronise with the Bus. The mains load switch is then 
closed in parallel with the Bus.  

 

NOTE:- This button is only active in MANUAL mode. 

 

NOTE:- If the bus is live when the manual button is pressed, 

synchronising will take place before the load switch is closed. 

mode. 

 

 

CLOSE GENERATOR 
This push button is used to control the closure of the generator load 
switching device and has two modes of operation : 
3.  Synchronising is NOT enabled. Pressing this button when the 

generator is running off load and in MANUAL mode, the generator load 
switch is closed. Further presses of this button will have no effect. 

4.  Synchronising is enabled. Pressing this button when the generator is 

running and in MANUAL mode, the 7510MK1 controller, will volts 
match and synchronise with the Bus. The generator load switch is then 
closed in parallel with the Bus.  

 

NOTE:- This button is only active in MANUAL mode. 

 

NOTE:- If the bus is live when the manual button is pressed, 

synchronising will take place before the load switch is closed. 

 

 

 

 

Summary of Contents for DSE7560































































Reviews:

No comments

Brands by name

Popular brands

Load more brands