Druck PV 210, Instruction Manual

Page: 5 / 44

Copyright 2005 Baker Hughes Company.
English–PV 210 Instruction Manual | 1
Introduction
This manual provides operating instructions for the PV 210
Low Pressure Pneumatic hand-pump.
Safety
The manufacturer has designed this equipment to be safe
when operated using the procedures detailed in this
manual. The user must not use this equipment for any other
purpose than that stated.
This manual contains safety and operating instructions that
must be followed to make sure of safe operation and to
keep the equipment in a safe condition. The safety
instructions are either warnings or cautions issued to
protect the user and the equipment from injury or damage.
Use suitably qualified technicians
*
and good engineering
practice for all procedures in this manual.
Pressure
Do not apply pressure greater than the maximum safe
working pressure stated in the specification.
Toxic Materials
There are no known toxic materials used in construction of
this equipment.
Maintenance
The equipment must be maintained using the procedures
in this publication. Further manufacturer’s procedures
should be done by an authorized service agents or the
manufacturer’s service departments.
Technical Advice
For technical advice contact the manufacturer or
subsidiary.
Symbols
The following symbols mark this equipment:
Abbreviations
The following abbreviations are used in this publication.
Note: Abbreviations are the same in the singular and
plural.
1. Introduction
The PV 210 is a portable source of pressure and vacuum.
Each pump includes a pressure/vacuum selector, a volume
control for fine adjustment and an adjustable pressure relief
valve to prevent damage to sensitive instruments.
2. Operation
Note:
Wherever possible, use o-ring seals in the BSP
connection ports this is the recommended method of
sealing.
Key to Figure A1
1. Pressure release valve.
2. Fine adjust vernier.
3. Pressure/Vacuum selector.
4. Quick-fit connectors.
5. 1
m (3.3 ft) x 3 mm (1/8”) flexible nylon hose (x2).
6. 1/4” female BSP or NPT adaptor.
7. Pump handle.
8. Adjustable pressure relief valve.
2.1 Hose/Adaptors (Figure A1)
To attach a hose (5) and adapter (6) to a connector (4),
turn the knurled nut on the connector counterclockwise.
* A qualified technician must have the necessary technical
knowledge, documentation, special test equipment and
tools to carry out the required work on this equipment.
Symbol Description
This symbol, on the equipment, indicates a warning
and that the user should refer to the user manual.
Ce symbole, sur l'appareil, est un avertissement qui
indique que l'utilisateur doit consulter le manuel
d'utilisation.
Do not dispose of this product as household waste.
Use an approved organization that collects and/or
recycles waste electrical and electronic equipment.
For more information, contact one of these:
- Our customer service department: Druck.com
- Your local government office.
Abbreviati
on
Description
°C degrees Celsius
BSP British Standard Pipe thread
COSHH Control of Substances Hazardous to Health
regulations
°F degrees Fahrenheit
ft lb foot pound
inH
2
O inches of water
inHg inches of mercury
lb pounds
kg kilogram
m metre
mm millimetre
MSDS Material Safety Data Sheet
NPT National Pipe Thread
psi pounds per square inch
PTFE polytetrafluoroethylene
WARNING
Before applying pressure, make
sure all connections are correct and
equipment is internally clean and free from
damage.
Make sure that all equipment is to the correct
pressure rating.
Do not exceed the maximum operating
pressure stated in the specification.
Observe the relevant health and safety
precautions.
CAUTION
If PTFE tape is used to seal NPT
threads, ensure that only a sufficient amount
is used to achieve pressure seal. If excess
tape is used, particles can become loose
during the connector mating process and
enter the pump, potentially leading to loss of
pump performance or pressure leaks.
INFORMATION
Because the PV 210 only
has a small displacement, only use the PV 210
to pressurize small volumes.
Abbreviati
on
Description