DriSteem Vaporstream Installation, Operation And Maintenance Manual Download Page 15 | Manualshive

Page: 15 / 80

background image

11

VAPORSTREAM INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

For overhead installations, install a drip pan to prevent possible water damage
(see ﬁ gure below).

Secure trapeze hanger to an overhead structure that is strong enough to
support the operating weight of the Vaporstream humidiﬁ er and ﬁ eld installed
piping, plus the weight of the control cabinet if it is mounted on the humidiﬁ er.

Adjust the mounting so that the tank sets level side to side and front to back.
Verify level after the tank is ﬁ lled and is at operating weight.

Mounting:

Cleanout

Provide 18"
(457 mm)
minimum
clearance
above cover

1¼" (DN32)
minimum

Drip pan
recommended
in overhead
installations
(by installer) to
prevent possible
water damage

25%
larger than
humidiﬁ er

Angle iron sized to properly
support humidiﬁ er

3/8" (M10) threaded rod of
length required

Humidiﬁ er drain to
appropriate building waste.
Do not drain humidiﬁ er
directly into drip pan. Install
water seal as shown in the
piping section of this manual

Secure rods to an overhead structure that is strong
enough to support the Vaporstream's operating weight.
See the weight tables in this document.

Overhead installation

Do not install water piping and humidiﬁ ers
above expensive apparatus or equipment.
A broken water pipe, leak ing valve gland,
condensation or other water leaks can occur
causing serious dam age and costly re pairs to
the equip ment below.

If this type of installation cannot be avoided,
install a drip pan constructed of galvanized
sheet metal under the hu mid i ﬁ er to catch
potential water drips (see Figure 11-1).

Pipe the overﬂ ow from the Vaporstream
directly to a ﬂ oor drain — do not drain the
Vaporstream into the drip pan. Terminate the
drip pan and the Vaporstream overﬂ ow drains
above an open ﬂ oor drain.

Provide 18"
(457 mm)
minimum
clearance
above cover

1¼" (DN32)
minimum

Drip pan
recommended
in overhead
installations (by
installer) to prevent
possible water
damage

25%
larger than
humidiﬁ er

Hanger plate

Angle iron

Humidiﬁ er drain to
appropriate building waste.
Do not drain humidiﬁ er
directly into drip pan. Install
water seal as shown in the
piping section of this manual

Cleanout

Secure channel to an overhead structure that is strong
enough to support the Vaporstream's operating weight.
See the weight tables in this document.

Vaporstream Models 2-1 through 5-1

Vaporstream Models 6-1 through 100-4

VLC-OM-038

INSTALLATION

FIGURE 11-1: TRAPEZE HANGER

VLC-OM-005

Trapeze hanger

«
...
13
14
15
16
17
...
»

Summary of Contents for Vaporstream

















































































Reviews:

No comments

Related manuals for Vaporstream

Brand: Zibro Pages: 24

Brand: omi Pages: 94

Brand: Emax Pages: 35

Brand: Mitsubishi Electric Pages: 28

Brand: Mitsubishi Electric Pages: 24

Brand: Field Controls Pages: 8

Brand: Comedes Pages: 15

Brand: Crane Pages: 12

Brand: Nordic Home Culture Pages: 38

Brand: Vaco Pages: 47

SYSTEM SAVER HP MM1736

Brand: WABCO Pages: 36

Brand: ARENDO Pages: 40

Brand: Hamilton Home Products Pages: 21

Brand: VDL Pages: 8

Brand: Vellgoo Pages: 27

Brand: Dryfix Pages: 32

Brand: Kenmore Pages: 17

Brand: Humidity Source Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands