DriSteem Vaporstream Installation, Operation And Maintenance Manual Download Page 42

Page: 42 / 80

VAPORSTREAM INSTALLATION, OPERATION, AND MAINTENANCE MANUAL

Table 38-1:
Maximum steam carrying capacity and length of interconnecting steam hose or tubing

Steam hose

Copper or stainless steel tubing

Hose I.D.

Maximum capacity

Maximum length

Tubing size

Maximum capacity

Maximum developed

length

inches

lbs/hr

kg/h

inches

lbs/hr

kg/h

1½

150

1½

150

250

113

220

100

1. When using steam hose, use DriSteem steam hose for best results.

Field-supplied hose may have shorter life and may cause foaming
in the evaporating chamber resulting in condensate discharge
at the dispersion assembly. Do not use steam hose for outdoor
applications.

2. Maximum recommended length for steam hose is 10' (3 m). Longer

distances can cause kinking or low spots.

450

204

100

750

340

100

125

1400

635

100

150

2300

1043

100

3. Insulate tubing to minimize loss of capacity and efﬁ ciency.
4. Developed length of tubing equals measured length plus 50% of measured

length, to account for ﬁ ttings.

Longer tubing lengths are possible at capacities lower than listed

maximums. Consult factory.

5. Requires ﬂ ange connection.

Note: Capacities and lengths in this table are based on total maximum pressure drop in hose or tubing of 5" wc (1250 Pa).

mc_091410_1050-VLC

Interconnecting piping requirements

INSTALLATION

Dispersion:

Summary of Contents for Vaporstream

















































































Search results

Summary of Contents for Vaporstream

Reviews:

Related manuals for Vaporstream

Brands by name

Popular brands

DriSteem Vaporstream, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for Vaporstream

Reviews:

Related manuals for Vaporstream

Brands by name

Popular brands