manualshive.com logo in svg

DragonWave Horizon Compact Plus, Product Manual

Share
Download
DragonWave Horizon Compact Plus Product Manual Download Page 90

DragonWave Inc.  

82

 

Horizon Compact Plus Release 1.0.1

 

                                                              Wireless Ethernet Product User Manual 

– Volume 2 

set rls link enable [on/off] 

When 

rls link control

 is set to 

on

, the data Ethernet port remains in a shutdown state after the 

RLS condition has been cleared.  The  Ethernet port is manually re-enabled by issuing the 

set 

rls link enable

 

on

 command.  The

 set rls link enable off

 command disables the Ethernet port. 

Procedure 14-1  
Configure Rapid Link Shutdown Options  

Perform  this  procedure  to  configure  the  Rapid  Link  Shutdown  Options  for  the  Horizon  Compact  Plus 
system.  When RLS is used, the Horizon Compact Plus Port 1 will be set to "down" during modem-to-
modem  communication  failure.    This  feature  allows  a  router  to  select  an  alternate  path  should  the 
modem-to-modem communications fail. 

Note

: To perform this procedure, you must have NOC user rights. 

Required Action 

Steps 

login 

Log in as a NOC user. 

View rls 

Displays the state of the Rapid Link Shutdown feature.  RLS provides 
the ability to shut down the Horizon Compact Plus Ethernet link (both 
endpoints) during system outages. 

The default is "off". 

Sequence:  

get rls

 press Enter 

The system responds: 

RLS option is :[off/on]. 

 

View rls status 

Displays the detailed status of the RLS configuration. 

   Sequence: 

    

get rls status

 press Enter 

The system responds (Example): 

RLS Option:                                   On Advanced 
Rapid Link Shutdown:                          Activated 
RLS Peer Mismatch:                            Activated 
Degrade Monitor State:                        Activated 
Hard Fault Monitor State:                     Acitvated 
Make RSL Threshold:                           OK 
Peer RLS State:                               OK 
Radio Interface State:                        Up 
Network Interface State:                      Down 
User Configured Establish FER:                8.82E-07 
Minimum Achievable Establish FER:             3.06E-07 
User Configured Shutdown FER:                 1.76E-04 
Minimum Achievable Shutdown FER:              3.06E-06 
User Configured Establish Monitor Time(mSec): 40000 
Actual Establish Monitor Time(mSec):          45517 
User Configured Shutdown Monitor Time(mSec):  3000 
Actual Shutdown Monitor Time(mSec):           4550 

 

 

Summary of Contents for Horizon Compact Plus









































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands