DragonWave Horizon Compact Plus Product Manual Download Page 155

Page: 155 / 200

Detailed CLI Command List

147

Horizon Compact Plus Release 1.0.1

Wireless Ethernet Product User Manual

– Volume 2

CLI Command

Description

get cos qinq itag

returns the protocol id of dot1q Q_in_Q inner tag.

get cos qinq otag

returns the protocol id of dot1q Q_in_Q outer tag.

get cos queue cbs

returns the committed burst size of the cos queues.

get cos queue cir

displays the CIR(Committed Information Rate) for user
traffic queues

get cos queue mapping

the table in the response to this command indicates the
assignment of dot1p cos value to user queue.

get cos type

returns the cos type.

get cos wfq weight

returns the cos wfq weight.

get date time

displays current Date and Time to the user.

get default gateway

gets the system default gateway.

get default ipconfig

displays default IP Configuration of the system.

get dropped frames threshold

returns the dropped frames threshold set by the user in %.

get dw access

displays the DW access.

get dynamic config change

returns the status (on/off) of the dynamic config change
feature.

get ecfm configuration-errors [vlan <vlan-
id(1-4094)>]

[interface

<interface-id>]

[switchname <context_name>]

Displays the ECFM configuration-related errors (CFM
leak, Conflicting VlanIds, Excessive Levels, etc).

get ecfm default-domain [switchname
<context_name>]

Displays the global Default-domain parameters along with
the modified parameters corresponding to a VLAN.

get ecfm domain [brief | domain-number(1-
32)] [switchname <context_name>]

Display information about the Ecfm maintenance domain.

get ecfm error-log [domain <domain-
name(1..20)>

levelid<level-id(0-7)>]

[unaware

vlan

<vlan-id(1-4094)>]

[switchname <context_name>]

Displays the Error Log containing the information about
the errors encountered on the MEP.

get

ecfm

errors

[domain

<domain-

name(1..20)> | levelid <level-id(0-7)>]
[switchname <context_name>]

Display continuity check error conditions logged on a
device since it was last cleared.

get ecfm frame delay buffer [brief] [one-way
| two-way] [level <level-id(0-7)>][unaware |
vlan

<vlan-id(1-4094)>]

[interface

<interface-number>][mac

<peer-mac-

address>]

Display the contents of the rolling buffer maintained for
Frame delaycalculations measured at various times.

get ecfm global information[switchname
<context_name>]

Displays ethernet CFM global information.

get  ecfm  loopback  cache  [brief]  [level
<level-id(0-7)>][unaware  |  vlan  <vlan-id(1-
4094)>]

Displays the Loopback transactions related information.

Summary of Contents for Horizon Compact Plus









































































































































































































Search results

Summary of Contents for Horizon Compact Plus

Reviews:

Brands by name

Popular brands

DragonWave Horizon Compact Plus, Product Manual

Search results

Summary of Contents for Horizon Compact Plus

Reviews:

Brands by name

Popular brands