Dräger Vamos Operating Instructions Manual Download Page 6

Page: 6 / 52

Important Safety Information

Operating Ins

tructions V

amos, 1

. US ed.

Definitions

Deﬁnitions

NOTE:

A NOTE provides additional information intended to

avoid inconveniences during operation.

Typing conventions in this manual

Display messages are printed in bold, e. g:

Apnea !!!

Screen keys and other controls are indicated as »

Control

«,

e.g:

Standby

Abbreviations and Symbols

Please refer to “Abbreviations and Symbols” on page 48 for
explanations.

Labels on the equipment

Please refer to “Labels” on page 42

WARNING !

A WARNING statement refers to conditions with a
possibility of personal injury if disregarded.

CAUTION !

A CAUTION statement designates the possibility of damage
to equipment if disregarded.

Inspection

examination of actual condition

Service

measures to maintain speciﬁed
condition

Repair

measures to restore speciﬁed condition

Maintenance

inspection, service, and repair, where
necessary

Preventive
Maintenance

maintenance measures at regular
intervals

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Summary of Contents for Vamos





















































Search results

Summary of Contents for Vamos

Reviews:

Related manuals for Vamos

Brands by name

Popular brands

Dräger Vamos, Operating Instructions Manual

Search results

Summary of Contents for Vamos

Reviews:

Related manuals for Vamos

Brands by name

Popular brands