Dräger Vamos Operating Instructions Manual Download Page 39

Page: 39 / 52

Troubleshooting

Operating Ins

tructions V

amos, 1

. US ed.

Troubleshooting

Vamos divides alarm messages into 3 priority, identiﬁed by
exclamation marks:

Warning = !!! Top priority message
Caution = !!

Medium priority message

Advisory = !

Low priority message

The table below is intended to help identifying possible
causes of an alarm message and to assist with prompt
corrective action.

Messages are listed in alphabetical order.

Fault

Cause

Remedy

Apnea

!!!

Breathing/ventilation stopped: No breath
detected by CO

measurement for 30 seconds

Immediately ventilate the patient!

Check that the breathing hoses are not
disconnected

Batt. low

Option

Capacity of the optional internal battery is less
than 10 % of full capacity

Connect device to mains power

Cal Error

Automatic gas calibration failure

Check that sample gas can ﬂow freely from
»

« port. Route sample line without kinking.

INOP

measurement failure

Call DrägerService

Des INOP

Anesthetic gas measurement failure

Call DrägerService

Enf INOP

Anesthetic gas measurement failure

Call DrägerService

Fan

The internal exhaust fan is not operating
correctly.

Call DrägerService

FetCO

FetCO

measured value high than max. alarm

limit

Check ventilation

FetCO

FetCO

measured value lower than min. alarm

limit

Check ventilation

Check that the sample line (Luer Lock) is ﬁrmly
connected

FiCO

FiCO

measured value higher than max. alarm

limit

Replace the soda lime in the patient system.

Check that both inspiratory and expiratory valves
(valve diaphragms) are functioning correctly

FiDes lo

The inspiratory measured value of the set
anesthetic gas is lower than the min. alarm limit

Check vaporizer setting

Check that the sample line (Luer Lock) is ﬁrmly
seated

FiDes hi

!!!

The inspiratory measured value of the set
anesthetic gas is higher than the max. alarm limit

Check vaporizer setting

FiEnf lo

The inspiratory measured value of the set
anesthetic gas is lower than the min. alarm limit

Check vaporizer setting

Check that the sample line (Luer Lock) is ﬁrmly
connected

FiEnf hi

!!!

The inspiratory measured value of the set
anesthetic gas is higher than the max. alarm limit

Check vaporizer setting

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Summary of Contents for Vamos





















































Search results

Summary of Contents for Vamos

Reviews:

Related manuals for Vamos

Brands by name

Popular brands

Dräger Vamos, Operating Instructions Manual

Search results

Summary of Contents for Vamos

Reviews:

Related manuals for Vamos

Brands by name

Popular brands