Dräger Vamos Operating Instructions Manual Download Page 11

Page: 11 / 52

Operating Concept

Operating Ins

tructions V

amos, 1

. US ed.

Central Control Knob

Operating Concept

Central Control Knob

The central control element is the turn-and-press "dial knob",
which has two functions:

Turn knob for selecting/setting

Press knob for confirming selections/settings.

●

Switch the monitor on with the ON/OFF switch on the back
panel. After the self-test, Vamos enters Standby mode.

The yellow LED in the »

« key lights up.

Switch to Operating mode with the »

« key.

The selection menu for volatile anesthetic agents is now
displayed. The previously selected anesthetic agent is marked
by an arrow.

The monitor prompts you to select the anesthetic agent used:
Halothane
Enﬂurane
Isoﬂurane
Sevoﬂurane
Desﬂurane

●

Turn dial knob to select the anesthetic agent.
The selected anesthetic agent is highlighted in black on an
orange background.

●

Press dial knob to confirm. The confirmed new anesthetic
agent is now displayed in orange on black and is marked by
an arrow.

To return to the main menu:

●

Press dial knob.

Parameters can be set from the main menu.

●

Turn or press dial knob to select main menu.

●

Turn dial knob to select a parameter in the main menu.
The selected parameter is highlighted in black characters
on an orange background.

●

Press dial knob to open the parameter menu.

●

Turn dial knob to set parameter.

●

Press dial knob to confirm parameter.
The confirmed parameter is displayed in orange on black
and is marked by an arrow.

●

Press dial knob to return to the main menu.

●

Press dial knob to return to the display of measurements.

0023

Vamos

Agent

exit

Hal

Enf

Iso

Hal – –
[%] – –

N2O – –
[%] – –

CO2 – –
[%] – –

[%]

[1/min]

Des

SpO2

Pulse

110

Sev

Alarm

Agent

Param.

Config.

CO2

Hal
[%]

N2O
[%]

CO2
[%]

[%]

[1/min]

Sound

SpO2

Pulse

110

SpO2

Cal

0.6

0.1

0.0

4.5

exit

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Summary of Contents for Vamos





















































Search results

Summary of Contents for Vamos

Reviews:

Brands by name

Popular brands

Dräger Vamos, Operating Instructions Manual

Search results

Summary of Contents for Vamos

Reviews:

Brands by name

Popular brands