Dräger Vamos Operating Instructions Manual Download Page 28

Page: 28 / 52

Operation in Measurement Mode

Operating Ins

tructions V

amos, 1

. US ed.

Configure Display Brightness and MEDIBUS Baud Rate

Conﬁgure Display Brightness and MEDIBUS
Baud Rate

The brightness of the display can be adjusted in two steps:

high, low

The following baud rates of the MEDIBUS RS 232 interface
can be selected:

1200, 9600, 19200

To set:

●

Turn or press dial knob to select main menu.

●

Turn dial knob to select »

Conﬁg.

« parameter.

●

Press dial knob to open the configuration menu

●

Turn dial knob to set display brightness

●

Press dial knob to confirm the setting.
The selected brightness is marked with an arrow.

●

Turn dial knob to set baud rate.

●

Press dial knob to confirm the setting.
The selected baud rate is marked with an arrow.

●

Press dial knob again to return to the measurement
display.

The settings for brightness and baud rate will be used until
they are changed by the user again.

high

Brightn.

low

Hal
[%]

N2O
[%]

CO2
[%]

[1/min]

[%]

1200

SpO2

Pulse

110

Config.

0.6

0.1

0.0

4.5

9600

MEDIBUS

(Baud)

19200

exit

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Summary of Contents for Vamos





















































Search results

Summary of Contents for Vamos

Reviews:

Related manuals for Vamos

Brands by name

Popular brands

Dräger Vamos, Operating Instructions Manual

Search results

Summary of Contents for Vamos

Reviews:

Related manuals for Vamos

Brands by name

Popular brands