Dräger Vamos Operating Instructions Manual Download Page 45

Page: 45 / 52

Technical Data

Operating Ins

tructions V

amos, 1

. US ed.

Operating Characteristics

Display range for Enﬂurane

0 to 10 Vol.%

Precision

±(0.15 Vol.% + 15 % rel.)

Resolution

0.1 Vol.%

Display range for Sevoﬂurane

0 to 10.0 Vol.%

Precision

±(0.15 Vol.% + 15 % rel.)

Resolution

0.1 Vol.%

Display range for Desﬂurane

0 to 22 Vol.%

Precision

±(0.15 Vol.% + 15 % rel.)

Resolution

0.1 Vol.%

Warm-up phase

4 min

Drift

Zero point

within the required speciﬁcations

Measurement of functional oxygen saturation SpO

Oxygen saturation SpO

1 to 100 % SpO

Resolution

1 % SpO

Precision (adults)

in the range 70 to 100 % SpO

Min. ±3,5 % SpO

in the range 1 to 69 % SpO

not speciﬁed

Precision (neonates)

in the range 70 to 100 % SpO

Min. ±4,5 % SpO

in the range 1 to 69 % SpO

not speciﬁed

Pulse rate

20 to 250/min

Resolution

1/min

Precision

±3/min

Trigger point

<1 s

Averaging

Slow

10 to 15 seconds

Normal

5 to 7 seconds

Fast

2 to 3 seconds

Sensors

Type

Compatible with the following Nellcor sensors:
Oxisensor, Oxiband and Durasensor

Wavelengths

660 nm (red), 920 nm (infrared)

Light energy

<10 mW

Acoustic pulse signal

A tone is generated for each pulse beat.

Operating Characteristics

AC line power supply

100 to 240 V, 50/60 Hz
15 V DC output

Sound emission corresponding to free ﬁeld
measurement over a reﬂective plane

max. 45 dB (A)

RETURN TO THIS MANUAL'S TABLE OF CONTENTS

RETURN TO CD-ROM TABLE OF CONTENTS

Summary of Contents for Vamos





















































Search results

Summary of Contents for Vamos

Reviews:

Related manuals for Vamos

Brands by name

Popular brands

Dräger Vamos, Operating Instructions Manual

Search results

Summary of Contents for Vamos

Reviews:

Related manuals for Vamos

Brands by name

Popular brands