Dover MagLink LX4 Configuration Manual Download Page 10

Page: 10 / 63

3.1 Safety Warnings

This manual contains many important Safety Alerts. There can be a risk of injury or damage to property if you
do not obey these alerts. The panels below show the types of safety warnings that can be seen and how
each is specified.

DANGER:

Indicates an immediately hazardous condition that, if not prevented,

will result in death or serious injury.

WARNING:

Indicates a possibly hazardous condition that, if not prevented,

could result in death or serious injury.

CAUTION:

Indicates a possibly hazardous situation that, if not prevented,

could result in minor or moderate injury.

NOTICE:

Indicates important information not related to hazards. A condition that, if not

prevented, can result in property damage.

SAFETY INSTRUCTIONS:

Indicates instructions and procedures related to safety or

gives the location of safety equipment

3.2 Information Panels

NOTE:

This panel gives more information about an instruction or procedure.

IMPORTANT:

This panel contains special information that is important and must be read

and obeyed.

M2051-EU Rev.: 1 Dover Fueling Solutions

Page 10

Summary of Contents for MagLink LX4
































































Search results

Summary of Contents for MagLink LX4

Reviews:

Related manuals for MagLink LX4

Brands by name

Popular brands

Dover MagLink LX4, Configuration Manual

Search results

Summary of Contents for MagLink LX4

Reviews:

Related manuals for MagLink LX4

Brands by name

Popular brands