Dover MagLink LX4 Configuration Manual Download Page 38 | Manualshive

Page: 38 / 63

background image

l

Calibration cycles max

: This is the maximum calibration cycles value parameter. This sets the

number of auto calibration cycles in which the segments will not be changed if the auto calibration
process is not complete. the minimum value is 5 and the maximum is 10.

l

Calibration cycles required

: This value specifies the Autocalibration status percentage (%).

When each segment of the specified auto calibration volume range is at this value, Autocalibration is
complete. Because there can be segments in an Autocalibration cycle that are not changed, some
segments can be changed more than the required value.

6.3.7 ACR Results

6.3.8 Reconciliation

l

Test vend

: This is the quantity of product used in the calibration of hose meters. In meter calibration,

there is a product quantity removed from the tank without a related sale. if

Unaccounted variance

is

greater than Test vend threshold, then it is reported as “Test vend” and it is not thought of as a “Loss”.

l

Unexpected sales (liters)

: An alarm will be caused when the tank is in a quiet mode (there are no

sales) and product loss is sensed.

l

Average time

: This specifies the time for the loss warning or loss alarm.

l

Loss warning (liters)

: A difference more than this threshold will cause a Loss Warning

M2051-EU Rev.: 1 Dover Fueling Solutions

Page 38

«
...
36
37
38
39
40
...
»

Summary of Contents for MagLink LX4
































































Reviews:

No comments

Related manuals for MagLink LX4

Brand: Larson Davis Pages: 193

Brand: Facom Pages: 116

Charge Analyzer 711

Brand: 3M Pages: 24

Brand: Rayjet Pages: 81

Brand: Radio Shack Pages: 44

Brand: Radiodetection Pages: 2

Brand: X-laser Pages: 17

Brand: Conrad Electronic Pages: 38

Brand: IDEAL Pages: 84

Brand: TAC Pages: 28

Brand: AKCP Pages: 16

Brand: Swann Pages: 106

Brand: DynAmp Pages: 43

Brand: BK Precision Pages: 21

Brand: Fluke Pages: 97

GenTwo PMA1000V2.4

Brand: M&C Pages: 110

Brand: Aqualytic Pages: 16

Brand: SCHOTT Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands