Dover MagLink LX4 Configuration Manual Download Page 54

Page: 54 / 63

DAILY REPORT

This report will show (see the image above):

The opening and closing stock for the day.

The delivered volume for the day.

The delivery variance for the day.

The tank depletion for the day.

The pump sales for the day.

PETROLEUM REPORT

For a given time period, this report will show (see the image above):

Accounting var

(variance): This is the sum of Operating variance and Delivery variance, shown in

liters and as a % of tank sales

Deliveries

: The quantity of liters delivered.

Delivery var

(variance): This is the Delivery variance. This is calculated as the difference between

ATG measured delivery and invoiced delivery (invoice detail entered manually during delivery report).
The result is shown in liters and as a % of tank sales.

Tank depletion

: The quantity of liters physically kept in the tank.

Pump sales

: The quantity of liters that were sold by the tank (as recorded by the dispensers).

Test vend

: The quantity of fuel that was pumped out of the tank during a pump calibration check.

M2051-EU Rev.: 1 Dover Fueling Solutions

Page 54

Summary of Contents for MagLink LX4
































































Search results

Summary of Contents for MagLink LX4

Reviews:

Related manuals for MagLink LX4

Brands by name

Popular brands

Dover MagLink LX4, Configuration Manual

Search results

Summary of Contents for MagLink LX4

Reviews:

Related manuals for MagLink LX4

Brands by name

Popular brands