Doran 4100L Instruction Manual Download Page 92

Page: 92 / 95

TECHNICAL SPECIFICATIONS

Display:

6-digit red LED, 0.43" high
8 red LED bar type annunciators 0.2"x0.4"
3 bargraph areas for OVER, ACCEPT, UNDER 0.35"x0.75"

Front Panel:

Flat membrane touch panel; 0.010" polycarbonate laminated
over electrical grade polyester. Deposited silver ink contacts
on switches; cross linked acrylic adhesive.

Load Cell Excitation:10 VDC Fixed, 240 ma max. (8 x 350 ohm load cells)

(+EXC = +5vdc, -EXC = -5vdc)

Analog Input Range: 1 mV/V nominal

Analog Sensitivity:

0.6 uV/grad minimum

Internal Update Rate:

512 updates/second typical

Displayed Update Rate:

Up to 20 updates/second

Resolution:

1:104,000 internal

1:3000 displayed

(standard)

1:6000 displayed

(precision)

1:10000 displayed

(super precision)

Power (120 V operation):

120 VAC, 50/60 Hz, 0.1 A (typical)
100 VAC

(minimum)

130 VAC

(maximum)

Power (240 V operation):

240 VAC, 50/60 Hz, 0.05 A (typical)
200 VAC

(minimum)

250 VAC

(maximum)

Fuse (120 V operation):

0.250 amp, 250 V time-delay

Fuse (240 V operation):

0.125 amp, 250 V time-delay

Fuse is soldered into PCB and is not field replaceable without
tools.

Section 13 Technical Specs and Options

Summary of Contents for 4100L
































































































Search results

Summary of Contents for 4100L

Reviews:

Doran 4100L, Instruction Manual, Page: 92 / 95

Search results

Summary of Contents for 4100L

Reviews: