manualshive.com logo in svg

Doran 4100L, Instruction Manual, Page: 17 / 95

Share
Download
Doran 4100L Instruction Manual Download Page 17

GROSS/

Switches between the gross and net weight modes.  The GROSS and NET 

NET 

annunciators indicate which mode the scale is currently in.  The 
TARE push-button is active in either mode, but the ZERO push-button is 
available only in the gross mode.

CONV

Each time this push-button is pressed, the digital weight display changes
from lb to kg (g) to oz to lb & oz.  The user may select 4, 3 or 2 way convert
via the menu.

PRINT

Initiates a manual serial data transmission each time pressed. Or selects 
current label buffer number when depressed for more than 2 seconds.

PROD

Used to recall or change the current product number.

UP/DOWN

Used to increase or decrease the tolerance, tare or product number

ARROWS

settings, or to select parameters in the setup mode.  Note:  When both 
UP/DOWN arrows are pressed at the same time,  scale will reset. 

OVER &

Used to recall or change the over or under checkweigh tolerance value.

UNDER

In any mode of operation, these push-buttons can be pressed to recall the 
current setting being used by the 4200.

TARE

Used to set or recall a tare weight values.  The ACCEPT indicator flashes
when a tare weight is displayed.  Only positive values may be entered for a
tare.  If an attempt is made to enter a negative tare, an error message "Er  t-"
or "Er tAr" will be displayed as a warning. The TARE button operation
depends upon the Tare Entry Mode selected in the parameter setup. 

DIGITAL DISPLAY

The 6 digit weight display is a bright easy-to-read, red LED display.  It shows the actual
weight on the scale in the weighing mode, recalled or new values for over, under or tare
values, and error messages as required.  The display is also used to display calibration
and setup  information (parameters and options).

UNIT ANNUNCIATORS

The Model 4200 supports the display of lb, kg, oz, g and lb-oz. When the indicator is in the
lb, kg, or oz display modes, their respective annunciators will be enabled.  When the
indicator is in the lb-oz display mode, both the "lb" and "oz" annunciators will be enabled.  If
the indicator is set up to start up in the g display mode, then the display will show gram
weight, and the "kg" annunciator will be enabled.

Section 3  Display and Keyboard

9

Summary of Contents for 4100L
































































































Reviews:

No comments