background image

OP001121

2-59

Operating Controls

4. Reclining Position Adjustment

Pulling up the right lever (4,Figure 138) allows the seat 
backrest to be moved forward or backward.

Sit with your back against the seat back when adjusting it. 
If your back is not touching the seat back, the seat back 
may suddenly move forward.

5. Armrest Angle Adjustment

The angle of each armrest can be adjusted by turning a 
dial (5, Figure 139) on bottom of armrest. When adjusting 
the angle, manually raise the armrest before turning the 
dial.

6. Lumbar Support Adjustment

A lumbar support is located in the seat back.

Turn the dial (6, Figure 139) counterclockwise to increase 
the force of the lumbar support

7. Headrest

The headrest (7, Figure 139) can be adjusted forward/
backward and up/down. Move it by holding both sides.

Figure 139 

5

8

6

9

7

FG000778

Summary of Contents for DX700LC



























































































































































































































































































































Reviews: